Notifier NI-100(A) - Manual (Page 2)

Page 2 of 2 — DN-6996:B • 12/07/2011
NOTIFIER® is a registered trademark of Honeywell International Inc.
©2011 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Made in the U.S. A.
Weight: 3.6 oz. (102 g).
Temperature: 0°C to 49°C (32°F to 120°F).
Relative humidity: 10% – 93%, noncondensing.
Listings and Approvals
Listings and approvals below apply to the NI-100(A) detector.
In some cases, certain modules may not be listed by certain
approval agencies, or listing may be in process. Consult fac-
tory for latest listing status.
•
UL Listed: S1115.
• ULC Listed: S1115.
• CSFM: 7271-0028:0233.
• MEA: 319-02-E Vol. II.
• Maryland State Fire Marshal: permit 2173.
• FM approved.
Product Line Information
NOTE: “A” suffix indicates ULC Listed model.
NI-100: Addressable ionization detector; B210LP base
included.
NI-100A: Same as above with ULC Listing; B210LPA base
included.
INTELLIGENT BASES
NOTE: “A” suffix indicates ULC Listed model.
NOTE: For details about intelligent bases and their mounting, see
DN-60054.
B210LP (A) : Plug-in detector base (included); standard U.S.
flanged low-profile mounting base.
B210LPBP: Bulk pack of B210LP; package contains 10.
B501
(A) : Standard European flangeless mounting base.
B501BP: Bulk pack of B501; package contains 10.
B200SR
(A) : Intelligent sounder base capable of producing
sound output with ANSI Temporal 3 or continuous tone.
Replaces B501BH series bases in retrofit applications.
B224RB
(A) : Plug-in System Sensor relay base. Screw termi-
nals: up to 14 AWG (2.0 mm²). Relay type: Form-C. Rating: 2.0
A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @
30 VDC inductive.
B224BI(A): Plug-in System Sensor isolator detector base.
Maximum 25 devices between isolator bases (see DN-6994).
ACCESSORIES
F110: Retrofit flange to convert B210LP(A) to match the
B710LP(A) profile, or to convert older high-profile bases to
low-profile.
F110BP: Bulk pack of F110; package contains 15.
F210: Replacement flange for B210LP(A) base.
RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Mounts to
a U.S. single-gang electrical box. For use with B501(A) and
B210LP(A) bases only.
SMB600: Surface mounting kit
M02-04-00:Test magnet.
M02-09-00: Test magnet with telescoping handle.
XR2B: Detector removal tool. Allows installation and/or
removal of detector heads from bases in high ceiling applica-
tions.
XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524
m) sections.
T55-127-010: Detector removal tool without pole.
BCK-200B: Black detector covers; box of 10.
WCK-200B: White detector covers; box of 10.