Notifier NBG-12 Series - Manual (Page 2)

Page 2 of 2 — DN-6643:A1 • 04/22/08
NOTIFIER®, SpectrAlert® Advance, and System Sensor® are registered
trademarks of Honeywell International Inc.
©2008 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Made in the U.S. A.
ENGINEERING/ARCHITECTURAL SPECIFICATIONS
Manual Fire Alarm Stations shall be non-code, with a key- or
hex-operated reset lock in order that they may be tested, and so
designed that after actual Emergency Operation, they cannot be
restored to normal except by use of a key or hex. An operated
station shall automatically condition itself so as to be visually
detected as activated. Manual stations shall be constructed of
red colored LEXAN (or polycarbonate equivalent) with clearly
visible operating instructions provided on the cover. The word
FIRE shall appear on the front of the stations in white letters,
1.00 inches (2.54 cm) or larger.* Stations shall be suitable for
surface mounting on matching backbox SB-10 or SB-I/O; or
semi-flush mounting on a standard single-gang, double-gang, or
4" (10.16 cm) square electrical box, and shall be installed within
the limits defined by the Americans with Disabilities Act (ADA) or
per national/local requirements. Manual Stations shall be Under-
writers Laboratories listed.
NOTE: *The words “FIRE/FUEGO” on the NBG-12LSP and NBG-
12LPSP shall appear on the front of the station in white letters,
approximately 3/4" (1.905 cm) high.
Pre-Signal Models
The NBG-12LPS and NBG-12LPSP pull stations are non-coded
manual pull stations which provide a FACP with two normally
open alarm initiating input signals. “Pre-signal” input is activated
by pushing in, then pulling down, the dual-action handle. A “gen-
eral” alarm input signal can be manually activated via a momen-
tary rocker switch mounted inside the unit. This general alarm
switch can only be accessed by opening the cover with the sup-
plied key/lock. See diagram at right.
Agency Listings and Approvals
The listings and approvals below apply to the NBG-12 Series
pull stations. In some cases, certain modules may not be listed
by certain approval agencies, or listing may be in process. Con-
sult factory for latest listing status.
• C(UL)US Listed: file S692.
• CSFM approved: file 7150-0028:199.
• FM approved (except NBG-12LPS, NBG-12LPSP).
• MEA approved: file 67-02-E (NBG-12, NBG-12L, NBG-12LOB,
NBG-12LA).
• Lloyd’s Register type approved: file 93/60141 (E3) (NBG-12,
NBG-12L, NBG-12LA, NBG-12LOB, NBG-12S).
• U.S. Coast Guard approved: files 161.002/23/3 (AFP-200 with
NBG-12, NBG-12L, NBG-12S); 161.002/42/1 (NFS-640 with
NBG-12, NBG-12L, NBG-12S); 161.002/27/3 (AFP1010/
AM2020 with NBG-12, NBG-12L, NBG-12S).
• Patented: U.S. Patent No. D428,351; 6,380,846; 6,314,772;
6,632,108.
Product Line Information
NBG-12S: Single-action pull station with pigtail connections,
hex lock.
NBG-12: Dual-action pull station with SPST N/O switch, screw
terminal connections, hex lock.
NBG-12L: Dual-action pull station with SPST N/O switch,
screw terminal connections, key lock.
NBG-12LSP: Same as NBG-12L with English/Spanish (FIRE/
FUEGO) labeling.
NBG-12LPS: Dual-action pull station with pre-signal option.
NBG-12LPSP: Same as NBG-12LPS with English/Spanish
(FIRE/FUEGO) labeling.
NBG-12LOB: Dual-action pull station with key lock, outdoor
applications listings (NBG-12LO), and backbox. Includes SB-I/O
indoor/outdoor backbox, and sealing gasket. Model will also
mount to WP-10 weatherproof backbox in retrofit applications.
NOTE: NBG-12LO not available separately;
NBG-12LO + approved backbox = NBG-12LOB.
Outdoor applications listings apply to NBG-12LOB combination.
NBG-12LA: Dual-action pull station with key lock and annuncia-
tor contacts.
SB-10: Surface-mount backbox, metal.
SB-I/O: Surface-mount backbox, plastic. (Included with NBG-
12LOB.)
BG12TR: Optional trim ring for semi-flush mounting.
WP-10: Outdoor use backbox.
17021: Keys, set of two. (Included with key-lock pull stations.)
17007: Hex key, 9/64". (Included with hex-lock pull stations.)
NOTE: For addressable NBG-12LX models, see data sheet
DN-6726.
Dimensions
NBG-12LPS
6
643d
im2
.wmf
66
43lp
s .wmf