Kenwood KDC-U7056BT - Manual (Page 7)

14 | KDC-U7056DAB/ KDC-U7056BT/ KDC-U7056BTL English | 15
DSP settings
4-4. Speaker setting
The speaker X’Over is automatically set when the
position and size of each speaker are selected from
the following items.
1 Press [SRC] to select a source other than
Standby (“STANDBY”).
Refer to
<Source selection> (page 10) .
2 Press [Control] knob.
Enters the Function setting mode.
3 Select “Audio Control” > “Pro Setup” >
“Speaker Setting” using [Control] knob.
For how to use [Control] knob, refer to
<3-3. How
to select the item> (page 9) .
4 Select a speaker type using [Control] knob.
Speaker type Setting item Setting value
“Front”
Front speaker
location
“ Door ”, “On Dash”, “Under Dash”
“SIZE” Front speaker size
“O.E.M.”, “8cm”, “10cm”, “12cm”,
“13cm”, “ 16cm ”, “17cm”, “18cm”,
“4x6”, “5x7”, “6x8”, “6x9”, “7x10”
“TW” Tweeter size
“None”, “Small”, “ Medium ”, “Large”
“Rear” Rear speaker
location
“ Door ”, “Rear Deck”
(“ 2nd Row ”, “3rd Row” [1] )
“SIZE” Rear speaker size
“None”, “O.E.M.”, “8cm”, “10cm”,
“12cm”, “13cm”, “ 16cm ”, “17cm”,
“18cm”, “4x6”, “5x7”, “6x8”, “6x9”,
“7x10”
“SubWoofer” “SIZE” Speaker Size Subwoofer
“None”, “16cm”, “20cm”, “ 25cm ”,
“30cm”, “38cm Over”
( Colored text : Factory setting)
[1] Value set when “Minivan” or “Minivan (Long)” is selected
as described in <4-3. Car type selection> (page 13) .
When Speaker network is set to 3 way
Speaker type Setting item Setting value
“Tweeter”
“SIZE” Tweeter size
“Small”, “ Medium ”, “Large”
“Mid Range” Mid Range
speaker
location
Mid range speaker location
“ Door ”, “On Dush”, “Under Dush”
“SIZE” Mid range speaker size
“O.E.M.”, “8cm”, “10cm”, “12cm”,
“13cm”, “ 16cm ”, “17cm”, “18cm”,
“4x6”, “5x7”, “6x8”, “6x9”, “7x10”
“Woofer” “SIZE” Subwoofer size
“None”, “16cm”, “20cm”, “ 25cm ”,
“30cm”, “38cm Over”
4-5. X’Over setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section
<4-4. Speaker setting> (page 14) .
1 Press [SRC] to select a source other than
Standby (“STANDBY”).
Refer to
<Source selection> (page 10) .
2 Press [Control] knob.
Enters the Function setting mode.
3 Select “Audio Control” > “Pro Setup” >
“X’Over” using [Control] knob.
For how to use [Control] knob, refer to
<3-3. How
to select the item> (page 9) .
4 Select a speaker type using [Control] knob.
Speaker type Setting item Setting value
“Front”
“FC” Front high pass filter
Through , 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
“SLOPE” [1] Front high pass slope
-6, -12 , -18, -24 dB/Oct
“GAIN” Front gain
-8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB
“Rear” “FC” Rear high pass filter
Through , 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
“SLOPE” [1] Rear high pass slope
-6, -12 , -18, -24 dB/Oct
“GAIN” Rear Gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“SubWoofer” “FC” Subwoofer low pass filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through Hz
“SLOPE” [1] Subwoofer slope
-6, -12 , -18, -24 dB/Oct
“GAIN” Subwoofer gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Subwoofer phase
“REV” (180°)/ “ NML ” (0°)
“Tweeter” “FC” Shelving filter
1, 1.6, 2.5, 4 , 5, 6.3, 8, 10, 12.5 kHz
“Volume” Tweete volume
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
( Colored text : Factory setting)
[1] Displayed only when “FC” is set to ”30” - “250”.
5 Select a setting item using [Control] knob.
6 Select a setting value using [Control] knob.
Exiting from the Function setting mode
Press and hold [ 1/6].
When Speaker network is set to 3 way
Speaker type Setting item Setting value
“Tweeter”
“FC” Tweeter high pass filter
1, 1.6, 2.5, 4 , 5, 6.3, 8, 10, 12.5 kHz
“SLOPE” Tweeter slope
-6, -12 dB/Oct
“GAIN” Tweeter gain
-8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Tweeter phase
“REV” (180°)/ “ NML ” (0°)
“Mid LPF” “FC” Mid range low pass filter
1, 1.6, 2.5, 4 , 5, 6.3, 8, 10, 12.5,
Through kHz
“SLOPE” Mid range low pass slope
-6, -12 dB/Oct
“GAIN” Mid range gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Mid range phase
“REV” (180°)/ “ NML ” (0°)
“Mid HPF” “FC” Mid range high pass filter
Through, 30, 40, 50, 60, 70, 80, 90,
100 , 120, 150, 180, 220, 250 Hz
“SLOPE” Mid range high pass slope
-6, -12 dB/Oct
“GAIN” Mid range gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Mid range phase
“REV” (180°)/ “ NML ” (0°)
“Woofer” “FC” Woofer low pass filter
30, 40, 50, 60, 70, 80, 90, 100 , 120,
150, 180, 220, 250, Through Hz
“SLOPE” Woofer low pass slope
-6, -12 dB/Oct
“GAIN” Woofer gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Woofer phase
“REV” (180°)/ “ NML ” (0°)
5 Select a setting item using [Control] knob.
6 Select a setting value using [Control] knob.
Exiting from the Function setting mode
Press and hold [ 1/6].