Teledex Millennium Series - Manual (Page 6)

INCLUDED IN YOUR PACKAGE
• Handset • Clear Plastic Overlay • AC Adapter for LCD Display Function
• Base Unit • Coiled Handset Cord
• User Guide • Two (2) Line Cords
CONNECTING THE MILLENNIUM TELEPHONE
1) Located on the left side of the Millennium (as the phone is facing you) is a modular
jack labeled TO HANDSET. Insert one end of the coiled handset cord into this jack
(you should hear the coil cord click when properly inserted).
2) Insert the other end of the coiled handset cord into the modular jack on the handset.
3) Turn the telephone so the back panel is facing you. Insert either end of a line cord into
the jack on the back of the telephone labeled LINE.
4) Insert the other end of the line cord into the jack on the AC adapter labeled TEL SET.
If display functions are not being used, insert this end of the cord into a telephone wall
outlet jack and proceed to step 8.
5) Insert one end of the other line cord into the jack on the AC adapter labeled LINE.
6) Insert the other end of this line cord into a telephone wall outlet jack.
7) Plug the AC adapter into an available, unswitched electrical wall outlet. The
Millennium’s backlit LCD should now display the start-up messages.
8) Once your telephone is connected, remove the plastic overlay and place the paper face-
plate over the keys. Replace the plastic overlay by hooking the tabs on the overlay into
the recessed slots located on both sides. The overlay is easiest to insert when; the left or
right side tabs are inserted first, and the middle of the overlay is slightly bowed to
allow for insertion of the other tabs.
LINE POWERED TELEPHONE FUNCTIONS
The Millennium telephone will function effectively in situations where AC power is inter-
rupted or is not available. AC powered Display Functions are described in MILLENNIUM
DISPLAY FUNCTIONS on page 6.
The following features only require connection to an active telephone line(s).
SELECTING LINE 1 AND LINE 2
The Millennium’s MPCTM technology makes selecting the correct line as easy as lifting
the handset. MPC technology prioritizes the ringing or idle line and reduces the confusion
of manually having to select a line.
PLACING A CALL
USING THE HANDSET
1) Lift the handset. The Millennium will select the appropriate “idle” line.
2) Listen for dial tone. Dial the desired number, or press a GUEST SERVICE AUTO
DIAL key to automatically dial a pre-programmed number.
3) To end the call, hang up by placing the handset back in the cradle.
USING THE SPEAKERPHONE
1) With the handset in the cradle, press the LINE 1 or LINE 2 keys. The Millennium will
go off hook on the selected line with speakerphone active.
OR
2
Press the SPEAKER key. The Millennium will select the appropriate “idle” line.
NOTE: The red SPEAKER LED will indicate that the speakerphone is active.
2) Listen for dial tone. Dial the desired number, or press a GUEST SERVICE AUTO
DIAL key to automatically dial a pre-programmed number.
3) To end call the call press the SPEAKER key again.
RECEIVING A CALL
An audible ring and a flickering red LED indicate an inbound call.
USING THE HANDSET
1) Lift the handset. The Millennium will select the ringing line.
2) To end the call hang up the handset.
USING THE SPEAKERPHONE
1) With the handset in the cradle, press the line key associated with the ringing line. The
Millennium will go off hook answering the ringing line with the speakerphone active.
OR
2) Press the SPEAKER key. The Millennium will select the ringing line and answer with
the speakerphone active.
Note: The red SPEAKER LED will indicate that the speakerphone is active.
CONFERENCE CALLS
The CONFERENCE key allows the user to originate or to include two parties in a three-
way phone conversation. Typical conference calls would be initiated by;
- User initiates two (2) calls
- User initiates one (1) call after receiving a call
- User includes two (2) callers
USER INITIATES TWO (2) CALLS:
1) Place call to first party.
2) Place the first party on hold by pressing the HOLD key.
3) Place call to second party using the available, unused line.
4) Press the CONF key. The parties will be connected.
The LCD will display:
USER INITIATES ONE (1) CALL:
1) Receive call from first party.
2) Place caller on hold by pressing the HOLD key.
3) Place call to second party using the available, unused line.
3