A.J. Antunes & Co VCT-2000 9210118 - Manual (Page 11)

VERTICAL CONTACT TOASTER
11
P/N 1010832 Rev. E 02/13
MAINTENANCE
WARNING
Turn the power off, unplug the power cord, and
allow the unit to cool down for 30 minutes before
performing any service or maintenance.
CAUTION
To prevent damage to the unit, do NOT use abra-
sive cleaners on the release sheet or belt wrap.
CAUTION
Failure to use Release Sheets may result in dam-
age to the unit and loss of warranty coverage.
Daily
NOTE: Pre-buttering/pre-oiling buns before feeding
them into the toaster leads to butter/oil accumula-
tion on the Release Sheet. This is normal, however
excessive buildup can lead to buns sticking and
burning. It is recommended that the Release Sheet
be replaced or cleaned once for every 6 hours of
operation. Dirty Release Sheets can be soaked in
hot, soapy water for later cleaning. Continue to
rotate Release Sheets, alternating between sides to
maximize usage.
Tools Required:
• Heat-Resistant Gloves
• Clean Towels
• Multipurpose Detergent Solution
• Sanitizer Solution
1. Turn the power off, unplug the power cord, and
clean the Release Sheet and Belt Wraps while
they are warm.
2. Put on heat-resistant gloves and remove the
Butter Wheel, Pan, and Heat Shield (Figure 1).
3. Wash the Butter Wheel, Pan, and Heat Shield in
a sink and wipe them with a damp sanitized towel
and allow them to air dry.
4. Remove the Release Sheet and place it on a
clean, flat dry surface.
5. Wipe the silver side of the Release Sheet with
a clean towel dampened with Multipurpose
Detergent Solution immediately followed by a
second clean towel dampened with sanitizer and
allow it to air dry before continuing.
6. Once the silver side is dry, repeat Step 5 on the
black side of the Release Sheet.
7. Open the front Conveyor Cover and firmly wipe
the Belt Wrap from left to right and top to bottom
with a clean towel dampened with Multipurpose
Detergent Solution immediately followed by a sec-
ond clean towel dampened with sanitizer.
8. Close the front Conveyor Cover, open the rear
Conveyor Cover, and clean the Belt Wrap as
described in Step 7.
9. Close the rear Conveyor Cover. Reinstall the
Heat Shield, plug in the power cord, turn the unit
on, count 15 seconds, then turn the unit off and
unplug the unit.
10. Open the rear Conveyor Cover again and clean
the newly exposed section of the Belt Wrap in
the same manner as before. Close the Conveyor
Cover.
11. Open the front Conveyor Cover again and clean
the newly exposed section of the Belt Wrap in the
same manner as before.
12. Close the front Conveyor Cover and wipe down
the outside of the toaster with a clean, damp,
sanitized towel.
13. Install the Release Sheet by draping it over both
sides of the Platen with the crease centered on
the Platen.
NOTE: To prolong the life of the Release Sheet,
rotate it from the black side to the silver side on a
daily or weekly basis.
14. Install the Bun Chute so the hooks are installed
over the lower rear Support Rod.
15. Install the Heat Shield with the Release Sheet
retainer clips securely over the Release Sheet
and Platen.
16. Reinstall the Butter Wheel and Pan, and plug in
the unit.
NOTE: Make sure the Heat Shield is activating the
Conveyor Safety Interlock Switch. The conveyors
will not rotate unless the Heat Shield is in place
and the Conveyor Safety Interlock Switch is
activated.
NOTE: Check the Release Sheet to make sure it is
not caught in the Conveyor. Additional Release
Sheets can be purchased through your Authorized
Service Agency under P/N 7000249 (3-Pack) or
7000250 (10-Pack).