Sony MPK-WE User Manual

Marine pack, Caisson étanche, Mpk-we

Advertising
background image

4-129-749-11(1)

Operating Instructions
Mode d’emploi
Manual de instrucciones

MPK-WE

© 2009 Sony Corporation Printed in Japan

Owner’s Record

The model and serial numbers are located inside of the unit.

Record the serial number in the space provided below.

Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. MPK-WE

Serial No. _________________________

Drip-proof packing

Garniture pare-gouttes

3

1

2

1

2

1

2

Grease (model No. 3-071-370-0 )

Maintenance

After recording in a location with a sea breeze, wash this unit thoroughly in fresh

water with the buckles fastened to remove salt and sand, then wipe with a soft dry

cloth. It is recommended that you submerge this unit in fresh water for about 30

minutes. If it is left with salt on it, metal portions may be damaged or rust may

form and cause water leakage.

If sun oil is on this unit, be sure to wash it off thoroughly using lukewarm water.

Wipe the inside of this unit with a soft dry cloth. Do not wash it with water.

Be sure to perform the above maintenance each time you use this unit. Do not use

any type of solvent such as alcohol, benzine or thinner for cleaning, as this might

damage the surface finish of this unit.
When storing this unit

Attach the spacer supplied with this unit to prevent wear of the O-ring. (See

illustration )

Prevent dust from collecting on the O-ring.

Lightly coat the O-ring with grease and insert it into the seating groove, then store

this unit in a cool, well-ventilated location. Do not fasten the buckle.

Avoid storing this unit in a cold, very hot or humid place, or together with

naphthalene or camphor, as these conditions might damage this unit.

Preparation

Replacing the attachment

The following procedures are explained using DSC-W290/W230.

For details, refer to the operating instructions of your camera.

* If you are using the DSC-W290, the following steps are not required because

the attachment A for the DSC-W290 is already attached to this unit at

purchase.

1 Open this unit. (-1)

Press the top and bottom OPEN buttons together  and release the buckle in

the direction of the arrow  to open this unit body.

Notes

Take care not to lose the spacer as you will need it to store this unit.

2 Replace the attachments.

Detach the DSC-W290 front attachment A and rear attachment A-1

(-2)

Grasp the front attachment A by the parts marked  in the illustration and lift

it straight out.

Press lightly with your finger inside wall of the rear attachment A-1 and lift it

straight out.

Use the front attachment and rear attachment that are made for your

camera (-2).

The illustration shows the DSC-W230 front attachment B and rear attachment

B-1.
Firmly press the points marked  in the illustration.

After replacing the attachment, press this unit buttons several times to check

their operation.

* After you remove the attachment from this unit and store it, it should not be

straightened before you store it. It can be damaged if stored while it is deformed.

Preparing the O-ring and drip-proof packing

1 Remove the O-ring.

2 Coat the O-ring with grease.

Clean off any sand or dirt on the O-ring, in the seating groove, or on this unit’s

body where it touches the O-ring. Coat the O-ring with a light, even layer of

grease.

3 Attach the O-ring to this unit.

4 Check the drip-proof packing for any sand or dirt.

Notes

Do not remove or apply grease to the drip-proof packing.

This unit’s body may be scratched or water may leak if the cover is closed with

sand or dirt on the O-ring or drip-proof packing.

Be sure to read the separate O-ring Maintenance Manual.

Important details regarding handling of the O-ring are described in this

manual.

Preparing the digital still camera

Install the camera in this unit in a room with low-humidity or a similar

environment. Opening or closing this unit in hot or humid locations may

result in fogging of the front glass.

1 Remove the strap from the camera.

2 Insert the battery pack and “Memory Stick Duo” media.

Be sure to use a fully charged battery pack.

Be sure that “Memory Stick Duo” media has enough space to record images.

3 Press the ON/OFF (Power) button to turn on the camera.

4 Select REC Mode. (-4)

To record digital images, select

(Scene Selection) by the Mode dial.

To record movies, select (Movie Mode) by the Mode dial.

5 Select Mode in REC Mode.

To record digital images under water, select (Underwater) on the LCD

screen.

To record movies under water, press the MENU button to display the mode

selection screen and select

(Underwater) on the LCD screen. (DSC-W290/

W275/W270 only)

6 Set the AF Illuminator to [Off].

The AF Illuminator cannot be used with this unit.

7 Check the lens and LCD screen for any dirt.

Notes

Underwater movie recording is available in DSC-W290/W275/W270 only. DSC-

W230/W220/W215/W210 do not have that function.

Installing the digital still camera in the marine pack

Always be sure to turn off the power when installing or removing the

camera. The lens may be damaged if the power is on.

1 Press the ON/OFF (Power) button to turn off the camera.

2 Install the camera in this unit. (-2)

Check that the camera is placed correctly.

3 Close this unit’s body and fasten the buckle. (-3)

Secure this unit body, and fasten the buckles until the top and bottom latches

catch.

Notes

When closing this unit’s body, make sure that there is no debris, sand, hair or any

other foreign matter on the O-ring or in the seating groove. Water leakage may

result if any foreign matter is caught in these places.

Buckle position when closing this unit’s body

Good example (-3)

Bad example (-3)

If you close the buckle as shown in -3, the buckle will be caught,

making it impossible to lock this unit.

Attaching the accessories

Attaching the hand strap

We recommend attaching the hand strap (supplied) before using this unit. (See

illustration )
Attaching the diffuser

We recommend attaching the diffuser when you record using flash.

Align the diffuser with the front protector and press it firmly as illustrated.
Attaching and detaching the LCD hood

How to attach (-)

1 Attach the supplied strap of the LCD hood to this unit.

2 Align the LCD hood with the attachment guide and press it

firmly as illustrated.

How to detach (-)

Spread the LCD hood and detach it from the guide.

Notes

Be careful not to pinch the hand strap or the accessory strap when you close this

unit body. A water leak may develop if they are caught in the body.

Using the Marine Pack

Recording

1 Turn on the power. (-1)

2 Press the shutter lever/shutter button to record images. (-2)

Using/Setting various functions

You can use the various functions of the camera installed in this unit.
Selecting the mode

Select the REC Mode using the Mode dial on this unit.

To record still images all REC Mode except for (Movie Mode)

To record movies

(Movie Mode)

* While you are recording movies, audio cannot be recorded correctly.

When you set REC mode to

(Scene Selection) or (Movie Mode), you

can select submode in that mode.

Press the MENU button on this unit and select the desired mode with

(Macro) or (Flash) button.

* We recommend that you use (Underwater) in the scene selection mode for

underwater still image recording, or

(Underwater) in the movie recording

mode for underwater movie recording (DSC-W290/W275/W270 only).

Notes

Underwater movie recording is available in DSC-W290/W275/W270 only. DSC-

W230/W220/W215/W210 do not have that function.
Selecting the underwater white balance

Adjusts the color tone in (Underwater) mode under

(Scene Selection) or in

(Underwater) mode under (Movie Mode).

(Auto)

The camera automatically adjusts color tones underwater so

they appear natural.

(Underwater 1) Adjusts for underwater conditions where blue is strong.
(Underwater 2) Adjusts for underwater conditions where green is strong.

(Flash)

Adjusts for use of flash underwater.

Notes

For DSC-W290/W275/W270 users

(Flash) in [Underwater White Balance] is not available.

[Underwater White Balance] is not available when the flash is set to [Flash

On].

For DSC-W230/W220/W215/W210 users

If you use the flash while the underwater white balance is set to other than

(Flash), [Underwater White Balance] is automatically set to (Auto).

Using the zoom (See illustration )

Press on the W side for wide-angle. (Subject appears farther away.)

Press on the T side for telephoto. (Subject appears closer.)

Notes

If you do not record any images for a certain time, the camera turns off

automatically to prevent the battery pack from running out. To use the camera

again, turn on the power again. For details, refer to the operating instructions

supplied with the camera.

If you use the flash when this unit is attached, the shooting distance may shorten

depending on the situation. It is recommended to use the underwater video light

HVL-ML20M (sold separately).

Reflected glare may occur depending on the shooting condition. If this happens,

change the condition.

You cannot use the smile shutter function of the DSC-W290/W275/W270 with

this unit.

Playing back

You can play back images on the LCD screen using the operation button. You

cannot hear the sound.

1 Turn on the power. (-1)

2 Press (Playback) button. (-2)

3 Select the desired image. (-3)

-3  To previous image

-3  To next image

For details, refer to the operating instructions supplied with the camera.

Removing the digital still camera

1 Turn off the power. (-1)

Be sure to turn off the power whenever installing or removing the

camera. The lens may be damaged if the power is on.

2 Press the top and bottom OPEN buttons together and release the

buckle in the direction of the arrow to open this unit body. (-2)

3 Remove the camera from this unit.

When the camera has been used for a long time, the camera heats up. Turn off

the power and leave for a while to cool down before removing the camera from

this unit.

Be careful not to drop the camera when removing it.

4 Cancel (Underwater) or

(Underwater).

5 Set the AF Illuminator to [Auto].

Notes

Before opening this unit, rinse it with tap water or fresh water and then wipe the

water off with a soft cloth. When opening it, be careful not to let any water from

your body, hair or wetsuit cuffs drip onto the camera.

Before making a dive

Before recording images underwater, first take this unit to a depth of about 1 m

(3.3 feet) and check that it operates properly and that there are no leaks, then

commence your dive.

Install the camera in this unit before diving, and avoid opening and closing this

unit while on board boats or at the seashore as much as possible. When installing

the camera, do it in a place that has as low a humidity as possible.

Before using this unit, make sure that no debris has been caught between the front

and back halves of this unit’s body.

Before using this unit, always check the number of recordable images and

remaining battery life.

Times that are suited for recording

The most suitable time for recording images is between 10:00 AM and 2:00 PM,

when the sun is directly overhead.

To record pictures in places where the sunlight does not reach well or at night,

please use the underwater video light HVL-ML20M (sold separately).

Troubleshooting

Symptom

Cause/Corrective Actions

There are drops of water

inside this unit.

There are scratches or cracks on the O-ring.

Replace the O-ring with a new one.

The O-ring is not set correctly.

Place the O-ring evenly in the groove.

The buckle is not fastened.

Fasten the buckle until it clicks.

The recording function

does not work.

The battery pack has run out.

Charge the battery pack fully.

The “Memory Stick Duo” media is full.

Insert another “Memory Stick Duo” media or

erase unneeded data from the “Memory Stick

Duo” media.

The write-protect tab on the “Memory Stick Duo”

media is set to LOCK.

Set the tab to the recording position or insert a

new “Memory Stick Duo” media.

The camera heats up.

Leave the camera in the cool place for a while to

cool down.

The playback image is not

displayed in the color you

expected. (When recording

underwater)

The camera may not be set to

(Underwater) or

(Underwater).

Check that the camera is set to

(Underwater) or

(Underwater).

The underwater white balance may not be set

correctly.

Check the underwater white balance setting of the

camera.

Specifications

Material

Plastic (PC, ABS), glass

Water-resistance

O-ring, buckle

Pressure-resistance

To a depth of up to 40 m (132 feet) underwater

Switches that can be externally operated

ON/OFF (Power), Shutter, Zoom (W/T), Mode, Control, MENU, Delete, HOME

(DSC-W230/W220/W215/W210 only), Playback

Dimensions

Approx. 148 Ч 112 Ч 89 mm (5 7/8 Ч 4 1/2 Ч 3 5/8 in.) (w/h/d)

(excluding the projecting parts)

Mass

Approx. 480 g (1 lb 1 oz.) (marine pack only)

Included items

Waterproof case (1)

Hand strap (1)

LCD hood (1)

Diffuser (1)

Front attachment A (for DSC-W290/W275/W270) (1)*

Rear attachment A-1 (for DSC-W290) (1)*

Rear attachment A-2 (for DSC-W275/W270) (1)

*Attached to the waterproof case at purchase.

Front attachment B (for DSC-W230/W220/W215/W210) (1)

Rear attachment B-1 (for DSC-W230) (1)

Rear attachment B-2 (for DSC-W220/W215/W210) (1)

Grease (1)

O-ring (1)

Spacer (1)

Set of printed documentation

Optional accessories

Arm kit VCT-MP1K

Underwater video light HVL-ML20M (must be used together with arm kit

VCT-MP1K and “InfoLITHIUM” (M series) battery pack, (M series battery

charger))

O-ring kit ACC-MP105

(Check for

on the package at the time of purchase.)

This unit allows the attachment of the products mentioned above as well as

SEA&SEA SUNPAK CO., Ltd. underwater accessories. For details of those

accessories, refer to the following website.

http://www.seaandsea.co.jp/products/accessory/mpk/index.html

Design and specifications are subject to change without notice.

Mode dial

Sélecteur de mode

Shutter lever

(Shutter button)

Manette du

déclencheur

(Déclencheur)

ON/OFF button

Touche ON/OFF

Zoom button

Touche de zoom

Spacer (remove to use this unit)

Entretoise (la retirer avant d’utiliser ce boîtier)

Drip-proof packing

Garniture pare-gouttes

O-ring

Joint torique

2

Shutter lever

(Shutter button)

Manette du déclencheur

(Déclencheur)

Front protector

Protection avant

Tripod receptacle

When using a tripod, use a tripod with 5.5 mm

or shorter screws. This unit cannot be firmly

fastened on a tripod with long screws. Doing so

might damage this unit.
Filetage pour pied photo

Si vous utilisez un pied photo, sa vis ne doit pas

dépasser 5,5 mm. Ce boîtier ne pourra pas être

fixé stablement si la vis du pied photo est plus

longue. De plus le boîtier peut être endommagé.

ON/OFF button

Touche ON/OFF

Hook for hand

strap

Crochet pour la

dragonne

Front glass

Vitre avant

Diffuser

Diffuseur

Buckle

Boucle

OPEN button

Touche OPEN

LCD hood

Pare-soleil de

l’écran LCD

Zoom (W/T) buttons

Touches de zoom (W/T)

Mode dial

Sélecteur de

mode

Operation buttons

Touches d’exploitation

Front attachment A (1)

(For DSC-W290/W275/W270)

Fixation avant A (1)

(Pour les DSC-W290/W275/W270)

3

Detaching the shutter lever

Retrait de la manette du déclencheur

The shutter lever is removable.

La manette du déclencheur peut être retirée.

Attaching the shutter lever

Fixation de la manette du déclencheur

1

2-

Rear attachment A-1 (1)

(For DSC-W290)

Fixation arrière A-1 (1)

(Pour le DSC-W290)

Front attachment B (1)

(For DSC-W230/W220/W215/W210)

Fixation avant B (1)

(Pour les DSC-W230/W220/W215/W210)

Rear attachment B-1 (1)

(For DSC-W230)

Fixation arrière B-1 (1)

(Pour le DSC-W230)

4

Waterproof Case

Marine pack

Boîtier étanche

Caisson étanche

button

Touche

(Flash) button

Touche (Flash)

MENU button

Touche MENU

(Macro) button

Touche (Macro)

(Self-timer) button

Touche (Retardateur)

(Playback)

button

Touche

(Lecture)

DISP (Display) button

Touche DISP (Affichage)

(Delete) button

Touche (Suppression)

English

Main Feature

Useable at a depth of up to 40 m (132 feet) underwater.

Marine Pack MPK-WE (referred to below as “this unit”) is exclusively for use

with the Sony Digital Still Camera (referred to below as “camera”) DSC-W290/

W275/W270/W230/W220/W215/W210. (Not all cameras are available in all

countries or regions.)

This unit is waterproof so the camera can be used in the rain, snow, at the beach,

or underwater.

Using this unit with the camera setting to (Underwater) or

(Underwater)

will enable you to record beautiful underwater images. (Underwater movie

recording is available in DSC-W290/W275/W270 only. DSC-W230/W220/W215/

W210 do not have that function.)

Precautions

When using this unit while diving, be sure to pay attention to the surrounding

situation. Lack of attention may cause an accident while diving.

In case a water leakage is occurred, be sure to pay attention to the surrounding

situation and surface following the safety rules for diving.

Do not subject the front glass to strong shock, as it may crack.

Avoid opening this unit at the beach or on the water. Preparation such as

installing the camera and changing the “Memory Stick Duo” media should be

done in a place with low humidity and no salty air.

Do not throw this unit into the water.

Avoid using this unit in places with strong waves.

Avoid using this unit under the following situations:

in a very hot or humid place.

in water hotter than 40˚C (104˚F).

at temperatures lower than 0˚C (32˚F).

In these situations moisture condensation or water leakage may occur and damage

this unit.

Use this unit for no longer than 30 minutes at a time in temperatures above 35˚C

(95˚F).

Do not leave this unit under direct sunlight in a very hot and humid place for a

long period of time. If you cannot avoid leaving this unit under direct sunlight, be

sure to cover this unit with a towel or other protection.

The camera heats up if it is used inside this unit for a long time. Before removing

the camera from this unit, leave this unit in the shade or other cool place for a

while to cool down.

When the camera overheats, it may automatically turn off or recording may

malfunction. To use the camera again, leave it in the cool place for a while to cool

down.

A loose or nipped O-ring, sand or dirt on the O-ring may cause water leaks

under water.

Be sure to check the O-ring before use.

For details, read the O-ring Maintenance Manual.

If sun oil is on this unit, be sure to wash it off thoroughly using lukewarm

water. If this unit is left with sun oil on its body, the surface of this unit may

become discolored or damaged (such as cracks on the surface).

Water leakage

If water happens to leak in, stop exposing this unit to water immediately.

If the camera gets wet, take it to the nearest Sony dealer immediately. Repair costs

must be borne by the customer.
Anti-fogging effect

Although the front glass of this unit has been treated for anti-fogging, be sure

to install the camera in this unit in a room with low-humidity room or a similar

environment.

Before use

Before using the camera underwater, first take this unit to a depth of about

1 m (3.3 feet) and check that the camera is operating properly and that this

unit is not leaking, then commence your dive.

In the unlikely event that a malfunction of this unit causes damage due to

water leakage, Sony does not guarantee against damages to the equipment

contained in it (camera, battery pack, etc.) and the recorded contents, nor

expenses entailed in the photography.

O-ring and Drip-proof packing

O-ring

This unit uses an O-ring to maintain its water resistance. For details, refer to the

separate O-ring Maintenance Manual.

Improper handling of the O-ring can result in water leakage.
Drip-proof packing

Do not remove or apply grease to the drip-proof packing. If the packing rises up or

is nipped, this may result in water leaks.

If the drip-proof packing comes off, refit it carefully so that it is not twisted.

(See illustration )
O-ring and drip-proof packing serviceable life

O-ring

The serviceable life of the O-ring varies with frequency of use of this unit and

conditions. Generally, it is about one year.
Drip-proof packing

Replace the drip-proof packing with a new one if you find scratches or cracks on it.
After replacing, check that no water leaks in.
Grease

Use the grease in the blue tube (supplied). Using the grease in the yellow tube or

other manufacturer’s grease will damage the O-ring, and cause water leaks.
O-ring, drip-proof packing and grease

You can obtain the O-ring, drip-proof packing and grease at the nearest Sony dealer.

O-ring (model No. 3-080-065-0 )

Drip-proof packing (model No. 3-080-066-0 )

Rear attachment A-2 (1)

(For DSC-W275/W270)

Fixation arrière A-2 (1)

(Pour les DSC-W275/W270)

Rear attachment B-2 (1)

(For DSC-W220/W215/W210)

Fixation arrière B-2 (1)

(Pour les DSC-W220/W215/W210)

DSC-W290/W275/W270

DSC-W230/W220/W215/W210

DSC-W290/W275/W270

DSC-W230/W220/W215/W210

MENU button/

(Delete) button

Touche MENU/

(Suppression)

(Macro) button

Touche (Macro)

(Playback)

button

Touche

(Lecture)

(Self-timer) button

Touche (Retardateur)

HOME button

Touche HOME

(Flash) button

Touche (Flash)

button

Touche

DISP (Display) button

Touche DISP (Affichage)

Digital still

camera/

Appareil

photo

numérique

Front

attachment/

Fixation

avant

Rear

attachment/

Fixation

arrière

DSC-W290

A

A-1

DSC-W275/

W270

A

A-2

DSC-W230

B

B-1

DSC-W220/

W215/

W210

B

B-2

Français

Caractéristiques principales

Utilisable sous l’eau jusqu’à une profondeur de 40 mètres (132 pieds).

Le caisson marin MPK-WE (appelé ci-dessous « ce boîtier ») est destiné à

être utilisé exclusivement avec les appareils photo numériques Sony (appelés

ci-dessous « l’appareil photo ») DSC-W290/W275/W270/W230/W220/W215/

W210. (Tous ces appareils photos numériques ne sont pas disponibles dans tous

les pays ou toutes les régions.)

Ce boîtier étanche permet d’utiliser l’appareil photo sous la pluie ou la neige, sur la

plage ou sous l’eau.

Vous pourrez faire des prises de vue magnifiques sous l’eau si vous utilisez ce

boîtier avec (Sous l’eau) or

(Sous l’eau).

(Vous pouvez filmer sous l’eau seulement avec les DSC-W290/W275/W270. Les

DSC-W230/W220/W215/W210 ne possèdent pas cette fonction.)

Précautions

Si vous utilisez ce boîtier pendant la plongée, faites attention à votre

environnement. Un manque d’attention peut causer un accident pendant la

plongée.

Si de l’eau devait pénétrer dans ce boîtier, faites attention à votre environnement et

remontez à la surface en respectant les règles de sécurité propres à la plongée.

Ne soumettez pas la vitre avant à des chocs trop forts, car elle pourrait se briser.

Evitez d’ouvrir ce boîtier sur la plage ou sur l’eau. Les préparatifs, tels que la mise

en place de l’appareil photo et le remplacement du « Memory Stick Duo » doivent

être effectués à l’abri de l’humidité et de l’air salin.

Ne pas jeter ce boîtier dans l’eau.

Evitez d’utiliser ce boîtier aux endroits exposés à de fortes vagues.

Evitez d’utiliser ce boîtier dans les situations suivantes :

à un endroit très chaud ou humide ;

dans une eau à plus de 40˚C (104 ˚F) ;

à des températures inférieures à 0˚C (32 ˚F).

Dans de telles situations, ce boîtier peut être endommagé par la condensation

d’humidité ou les infiltrations d’eau.

Ne pas utiliser ce boîtier pendant plus de 30 minutes à une température

supérieure à 35˚C (95 ˚F).

Ne pas laisser ce boîtier en plein soleil à un endroit très chaud et humide pendant

longtemps. Si ce boîtier doit rester longtemps exposé au soleil, veillez à le

recouvrir d’une serviette ou d’un tissu quelconque.

L’appareil photo devient chaud s’il est utilisé pendant un certain temps avec ce

boîtier. Avant de retirer l’appareil photo de ce boîtier, laissez ce boîtier un moment

à l’ombre ou à un endroit frais pour qu’il refroidisse.

Lorsque l’appareil photo est trop chaud, il peut s’éteindre ou l’enregistrement peut

ne pas s’effectuer normalement. Laissez l’appareil photo un moment à un endroit

frais avant de le réutiliser.

Une infiltration d’eau dans ce boîtier peut être due à un joint torique détendu

ou coupé, à des grains de sable ou à de la poussière sur le joint torique.

Veillez à bien vérifier le joint torique avant d’utiliser ce boîtier.

Pour de plus amples informations, reportez-vous à la notice du joint torique.

Si de l’huile solaire devait tomber sur ce boîtier, prenez soin de l’enlever avec de

l’eau tiède. Si vous laissez ce boîtier avec des taches d’huile au soleil, sa surface

risque de se décolorer ou d’être endommagée (elle peut se craqueler).

Infiltration d’eau

Si de l’eau devait pénétrer dans ce boîtier, retirez-le immédiatement de l’eau.

Si l’appareil photo devait être mouillé, portez-le immédiatement au revendeur Sony

le plus proche. Les frais de réparation seront à la charge du client.
Effet anti-buée

Bien que la vitre avant de ce boîtier ait été traitée pour prévenir la formation de

buée, veillez à installer l’appareil photo dans ce boîtier dans une pièce non humide

ou à un endroit similaire.

Avis

Avant d’utiliser l’appareil photo sous l’eau et avant la plongée, mettez ce

boîtier dans l’eau à une profondeur de 1 m (3,3 pieds) et assurez-vous d’une

part que l’appareil photo fonctionne correctement et d’autre part que ce

boîtier est bien étanche.

Si une défectuosité du boîtier devait provoquer des dégâts à la suite d’une

infiltration d’eau, Sony ne garantira pas les dégâts causés à l’appareil qu’il

contient (appareil photo numérique, batterie, etc.) ni le contenu de la prise

de vue ou les frais liés à la prise de vue.

Joint torique et garniture pare-gouttes

Joint torique

L’étanchéité de ce boîtier est garantie par un joint torique. Pour de plus amples

informations, reportez-vous à la notice séparée du joint torique.

Une infiltration d’eau peut être due à une mauvaise manipulation du joint torique.
Garniture pare-gouttes

N’enlevez pas et n’appliquez pas de graisse sur la garniture pare-gouttes. Si la

garniture ressort ou est abîmée, de l’eau risque de pénétrer dans le boîtier.

Si la garniture pare-gouttes se détache, remettez-la délicatement dans la rainure sans

la tordre. (Voir l’illustration )
Durée de vie du joint torique et de la garniture pare-gouttes

Joint torique

La durée de vie du joint torique varie selon la fréquence et les conditions

d’utilisation de ce boîtier. Le joint torique dure environ un an.
Garniture pare-gouttes

Remplacez la garniture pare-gouttes par une neuve si elle est rayée ou craquelée.
Une fois le remplacement effectué, assurez-vous que le boîtier est étanche.
Graisse

Utilisez la graisse du tube bleu (fourni). L’emploi de la graisse du tube jaune ou

de la graisse d’une autre marque peut endommager le joint torique et causer des

infiltrations d’eau.
Joint torique, garniture pare-gouttes et graisse

Vous pouvez vous procurer un joint torique, une garniture pare-gouttes et de la

graisse auprès du revendeur Sony le plus proche.

Joint torique (référence : 3-080-065-0 )

Garniture pare-gouttes (référence : 3-080-066-0 )

Graisse (référence : 3-071-370-0 )

Entretien

Après une prise de vue à un endroit exposé à la brise marine, lavez soigneusement

ce boîtier à l’eau douce, en laissant la boucle bien fermée, pour enlever le sel et

le sable, puis essuyez-le avec un chiffon doux et sec. Il est conseillé de laisser ce

boîtier dans de l’eau douce pendant 30 minutes environ. Si le caisson n’est pas bien

nettoyé, le sel restant peut attaquer les deux parties métalliques et causer de la

corrosion, et par la suite une infiltration d’eau.

Si de l’huile solaire devait tomber sur ce boîtier, prenez soin de l’enlever avec de

l’eau tiède.

Essuyez l’intérieur de ce boîtier avec un chiffon doux et sec. Ne le lavez pas à l’eau.

Effectuez toutes les opérations mentionnées ci-dessus chaque fois que vous utilisez

ce boîtier. N’utilisez pas de solvant, comme de l’alcool, de la benzine ou du diluant

pour le nettoyage, car ces substances peuvent attaquer la finition de ce boîtier.
Avant de ranger ce boîtier

Fixez l’entretoise fournie avec ce boîtier pour que le joint torique ne s’use pas.

(Voir l’illustration )

Eviter d’exposer le joint torique à la poussière.

Recouvrez légèrement le joint torique de graisse et insérez-le dans la rainure, puis

rangez ce boîtier à un endroit frais et bien aéré. Ne fermez pas la boucle.

Evitez de ranger ce boîtier à un endroit froid, très chaud ou humide, ou à

proximité de naphtaline ou de camphre. Cela pourrait l’endommager.

Préparatifs

Remplacement de la fixation

Les opérations suivantes concernent les DSC-W290/W230.

Pour de plus amples informations, reportez-vous au mode d’emploi de votre

caméscope.

* Si vous utilisez le DSC-W290, les points suivants sont inutiles parce que la

fixation A du DSC-W290 a été mise en place en usine.

1 Ouvrez ce boîtier. (-1)

Appuyez en même temps sur les touches OPEN du haut et du bas  et ouvrez la

boucle dans le sens de la flèche  pour ouvrir les deux parties du boîtier.

Remarques

Faites attention de ne pas perdre l’entretoise car vous devrez la remettre dans ce

boîtier avant de le ranger.

2 Remplacez les fixations.

Détachez la fixation avant A et la fixation arrière A-1 du DSC-W290

(-2)

Saisissez la fixation avant A aux endroits indiqués par  sur l’illustration et

tirez-la tout droit.

Appuyez légèrement avec le doigt à l’intérieur de la fixation arrière A-1 et

tirez-la tout droit.

Utilisez la fixation avant et la fixation arrière prévues pour votre

appareil photo (-2).

Les illustrations montrent la fixation avant B et la fixation arrière B-1 du DSC-

W230.
Appuyez fermement aux endroits indiqués par  sur l’illustration.

Après avoir remplacé la fixation, appuyez plusieurs fois sur les touches de ce

boîtier pour vous assurer qu’elles fonctionnent.

* Ne redressez pas la fixation de ce boîtier après l’avoir retirée et avant de la ranger.

Elle peut être endommagée si elle est déformée lorsque vous la rangez.

Préparation du joint torique et de la garniture pare-

gouttes

1 Retirez le joint torique.

2 Mettez de la graisse sur le joint torique.

Enlevez le sable ou la saleté présente sur le joint torique, dans la rainure du

joint ou sur les deux parties du boîtier touchant le joint torique. Revêtez

uniformément le joint torique d’une fine couche de graisse.

3 Insérez le joint torique dans ce boîtier.

4 Assurez-vous qu’il n’y a pas de sable ou saleté sur la garniture pare-

gouttes.

Remarques

N’enlevez pas et n’appliquez pas de graisse sur la garniture pare-gouttes.

Les deux parties de ce boîtier peuvent être rayées ou de l’eau peut s’infiltrer s’il y

a du sable ou de la saleté sur le joint torique ou la garniture pare-gouttes lorsque

vous fermez le couvercle.

Veillez à lire la notice séparée du joint torique.

Vous trouverez dans cette notice des détails importants sur le joint

torique.

Préparation de l’appareil photo numérique

Mettez l’appareil photo dans ce boîtier dans une pièce non humide ou

dans un lieu similaire.

La vitre avant se couvrira de buée si vous ouvrez ou fermez ce boîtier

dans un lieu chaud ou humide.

1 Détachez la dragonne de l’appareil photo.

2 Insérez la batterie et un « Memory Stick Duo ».

La batterie doit être pleine.

Le « Memory Stick Duo » doit disposer de suffisamment d’espace pour les photos

ou le film que vous voulez prendre.

3 Appuyez sur la touche ON/OFF (Alimentation) pour mettre l’appareil

photo sous tension.

4 Sélectionnez le mode REC. (-4)

Pour prendre des photos numériques, sélectionnez

(Sélection scène) avec le

sélecteur de mode.

Pour filmer, sélectionnez (Mode film) avec le sélecteur de mode.

5 Sélectionnez le mode REC.

Pour prendre des photos numériques sous l’eau, sélectionnez (Sous l’eau) sur

l’écran LCD.

Pour filmer sous l’eau, appuyez sur la touche MENU pour afficher la page de

sélection de mode et sélectionnez

(Sous l’eau) sur l’écran LCD. (DSC-W290/

W275/W270 seulement)

6 Réglez l’illuminateur AF sur [Désact].

L’illuminateur AF ne peut pas être utilisé avec ce boîtier.

7 Vérifiez si l’objectif et l’écran LCD sont propres.

Remarques

Vous pouvez filmer sous l’eau seulement avec les DSC-W290/W275/W270. Les

DSC-W230/W220/W215/W210 ne possèdent pas cette fonction.

Mise en place de l’appareil photo dans le caisson

étanche

Veillez à mettre l’appareil photo hors tension avant de l’installer ou de le

sortir du boîtier. Sinon l’objectif pourrait être endommagé.

1 Appuyez sur la touche ON/OFF (Alimentation) pour mettre l’appareil

photo hors tension.

2 Installez l’appareil photo dans ce boîtier. (-2)

Assurez-vous que l’appareil photo est bien en place.

3 Fermez les deux parties de ce boîtier et verrouillez la boucle. (-3)

Les taquets du haut et du bas de la boucle doivent être encliquetés pour que ce

boîtier soit bien fermé.

Remarques

Lorsque vous fermez les deux parties de ce boîtier, assurez-vous qu’il n’y a pas de

saleté, sable, cheveux ou d’autres matières sur le joint torique ou dans sa rainure.

Si des matières étrangères sont prises à ces endroits, de l’eau peut pénétrer dans

ce boîtier.

Position de la boucle lors de la fermeture des deux parties de ce

boîtier

Bon (-3)

Mauvais (-3)

Si vous fermez la boucle comme indiqué dans -3, elle se coincera et ce boîtier

ne pourra pas être verrouillé.

Fixation des accessoires

Fixation de la dragonne

Il est conseillé de fixer la dragonne (fournie) avant d’utiliser ce boîtier. (Voir

l’illustration )
Fixation du diffuseur

Il est conseillé de fixer le diffuseur si vous utilisez le flash pour la prise de vue.

Alignez le diffuseur sur le protecteur avant et appuyez fermement dessus de la façon

illustrée.
Fixation et retrait du pare-soleil de l’écran LCD

Fixation (-)

1 Fixez la lanière fournie du pare-soleil de l’écran LCD à ce boîtier.

2 Alignez le pare-soleil de l’écran LCD avec le guide et appuyez

fermement de la façon illustrée.

Retrait (-)

Ecartez le pare-soleil de l’écran LCD et détachez-le du guide.

Remarques

Attention de ne pas coincer la dragonne ou la lanière de l’accessoire lorsque vous

fermez les deux parties de ce boîtier. Sinon le boîtier risque de laisser l’eau s’infiltrer.

Utilisation du caisson étanche

Enregistrement

1 Mettez l’appareil photo sous tension. (-1)

2 Appuyez sur la manette du déclencheur/le déclencheur pour

prendre des photos. (-2)

Utilisation et réglage des diverses fonctions

Vous pouvez utiliser les diverses fonctions de l’appareil photo quand il est dans ce

boîtier.
Sélection du mode

Sélectionnez le mode REC avec le sélecteur de mode de ce boîtier.

Pour prendre des photos Tous les modes REC sauf (Mode film)

Pour filmer

(Mode film)

* Lorsque vous filmez, le son ne peut pas s’enregistrer correctement.

Lorsque vous réglez le mode REC sur

(Sélection scène) ou sur

(Mode Film), vous avez le choix entre différents modes secondaires.

Appuyez sur la touche MENU de ce boîtier et sélectionnez le mode souhaité avec

la touche (Macro) ou (Flash).

* Il est conseillé d’utiliser (Sous l’eau) dans le mode de sélection de scène pour

prendre de photos sous l’eau ou

(Sous l’eau) dans le mode d’enregistrement

de film pour filmer sous l’eau (DSC-W290/W275/W270 seulement).

Remarques

Vous pouvez filmer sous l’eau seulement avec les DSC-W290/W275/W270. Les

DSC-W230/W220/W215/W210 ne possèdent pas cette fonction.
Sélection de la balance des blancs sous l’eau

Permet de régler les teintes des couleurs dans le mode (Sous l’eau) de

(Sélection scène) ou dans le mode

(Sous l’eau) de (Mode film).

(Auto)

L’appareil photo ajuste automatiquement les teintes des

couleurs pour qu’elles paraissent plus naturelles.

(Sous l’eau 1) Ajuste la balance des blancs lorsque le bleu prédomine.
(Sous l’eau 2) Ajuste la balance des blancs lorsque le vert prédomine.

(Flash)

Ajuste la balance des blancs pour la prise de vue sous l’eau au

flash.

Remarques

Pour les utilisateurs des DSC-W290/W275/W270

(Flash) dans [Balance blanc sous l’eau] n’est pas disponible.

[Balance blanc sous l’eau] n’est pas disponible lorsque le flash est réglé sur

[Flash activé].

Pour les utilisateurs des DSC-W230/W220/W215/W210

Si vous utilisez le flash lorsque la balance des blancs sous l’eau est réglée

sur autre chose que (Flash), [Balance blanc sous l’eau] se règle

automatiquement sur (Auto).

Utilisation du zoom (Voir l’illustration )

 Appuyez sur le côté W pour un zoom arrière. (Le sujet semble s’éloigner.)

 Appuyez sur le côté T pour un zoom avant. (Le sujet semble se rapprocher.)

Remarques

Si vous ne prenez pas de photos ou ne filmez pas pendant un certain temps,

l’appareil photo se mettra de lui-même hors tension pour préserver la batterie.

Pour utiliser de nouveau l’appareil photo, remettez-le sous tension. Pour plus

d’informations, reportez-vous au mode d’emploi fourni avec l’appareil photo.

Si vous utilisez le flash quand l’appareil photo est dans ce boîtier, la distance

de prise de vue peut être plus courte dans certaines situations. Dans ce cas il

est conseillé d’utiliser une torche vidéo sous-marine HVL-ML20M (vendue

séparément).

Dans certaines situations, des reflets seront visibles lors de la prise de vue. Dans ce

cas, changez de position.

Vous ne pouvez pas utiliser la fonction de détection du sourire des DSC-W290/

W275/W270 avec ce boîtier.

Lecture

Vous pouvez voir les images sur l’écran LCD à l’aide de la touche d’exploitation. Le

son par contre n’est pas audible.

1 Mettez l’appareil photo sous tension. (-1)

2 Appuyez sur la touche (Lecture). (-2)

3 Sélectionnez l’image souhaitée. (-3)

-3  Pour voir l’image précédente

-3  Pour voir l’image suivante

Pour plus d’informations, reportez-vous au mode d’emploi fourni avec l’appareil

photo.

(Suite à la page arrière)

Advertising