CatEye CC-VL520/CC-VL820 [Velo 7/Velo 9] - Manual (Page 3)

VELO 9 / VELO 7 ENG 3
Operation test
After installed, check that the computer displays the speed by turning
the front wheel. When it is not displayed, check the installation condi-
tions and again (page 2).
Preparing the computer
Perform the clear all data operation as shown below, when you use the
unit for the fi rst time or restore the unit to the condition checked at the
factory.
1
Clear all data (initialization)
Press the AC button on the back of the computer.
2
Select the speed unit
Select “km/h” or “mph”.
MODE
km/h ↔ mph
SET
Register the
setting
3
Set the tire size
Set the tire size by either one of the following methods.
Simple setting (select from the tire size)
Pressing the MODE button changes 26” → 700c
→ 27” → 205[] → 16” → 18” → 20” → 22” →
24” → 26” in order. Select the tire size (inch) of
your bicycle, and then press the SET button.
* Generally, the tire size is indicated on the side
of the tire.
MODE
Switching size
SET
Register
the setting
MODE
Press and hold to the
MODE button with
“205[]” displayed to
change to the wheel
size entry screen.
Detailed setting (enter the numeric value of the tire circumference)
* Entering the tire circumference ensures more accurate measure-
ments.
1 With 205[] displayed on the screen, press and
hold the MODE button.
2 Pressing the MODE button increases the nu-
meric value flashing, whereas pressing and
holding the MODE button moves the digit. En-
ter any value of the circumference in cm, and
then press the SET button.
* Use “Tire circumference reference table” as a
guide.
MODE
Increase
the value
MODE
Move digits
(Press &
hold)
SET
Register the
setting
AC
Tire circumference
You can fi nd the tire circumference (L) of your tire size in the chart be-
low, or actually measure the tire circumference (L) of your bicycle.
• How to measure the tire circumference (L)
For the most accurate measurement, do a wheel roll
out. With the tires under proper pressure, place the
valve stem at the bottom. Mark the spot on the fl oor
and with the rider’s weight on the bike, roll exactly one
wheel revolution in a straight line (until the valve comes around again to
the bottom). Mark where the valve stem is and measure the distance.
• Tire circumference reference table
* Generally, the tire size or ETRTO is indicated on the side of the tire.
L cm
ETRTO Tire size L (cm)
40-254 14x1.50 102
47-254 14x1.75 110
40-305 16x1.50 119
47-305 16x1.75 120
54-305 16x2.00 125
28-349 16x1-1/8 129
37-349 16x1-3/8 130
32-369 17x1-1/4 (369) 134
40-355 18x1.50 134
47-355 18x1.75 135
32-406 20x1.25 145
35-406 20x1.35 146
40-406 20x1.50 149
47-406 20x1.75 152
50-406 20x1.95 157
28-451 20x1-1/8 155
37-451 20x1-3/8 1625
37-501 22x1-3/8 177
40-501 22x1-1/2 179
47-507 24x1.75 189
50-507 24x2.00 193
54-507 24x2.125 197
25-520 24x1(520) 175
24x3/4 Tubular 179
28-540 24x1-1/8 180
32-540 24x1-1/4 191
25-559 26x1(559) 191
32-559 26x1.25 195
37-559 26x1.40 201
40-559 26x1.50 201
47-559 26x1.75 202
50-559 26x1.95 205
54-559 26x2.10 207
57-559 26x2.125 207
58-559 26x2.35 208
75-559 26x3.00 217
28-590 26x1-1/8 197
ETRTO Tire size L (cm)
37-590 26x1-3/8 207
37-584 26x1-1/2 210
650C Tubular
26x7/8
192
20-571 650x20C 194
23-571 650x23C 194
25-571 650x25C
26x1(571)
195
40-590 650x38A 213
40-584 650x38B 211
25-630 27x1(630) 215
28-630 27x1-1/8 216
32-630 27x1-1/4 216
37-630 27x1-3/8 217
40-584 27.5x1.50 208
50-584 27.5x1.95 209
54-584 27.5x2.1 215
57-584 27.5x2.25 218
18-622 700x18C 207
19-622 700x19C 208
20-622 700x20C 209
23-622 700x23C 210
25-622 700x25C 211
28-622 700x28C 214
30-622 700x30C 215
32-622 700x32C 216
700C Tubular 213
35-622 700x35C 217
38-622 700x38C 218
40-622 700x40C 220
42-622 700x42C 222
44-622 700x44C 224
45-622 700x45C 224
47-622 700x47C 227
54-622 29x2.1 229
56-622 29x2.2 230
60-622 29x2.3 233
MODE AC
SET
Battery case cover
Contact
4
Set the Clock
Pressing and holding the MODE button switches the
display to “Display format”, “Hour”, and “Minute” in
order.
MODE
12h ↔ 24h, or
increases the
value
MODE
Switch the
screen or move
digits
5
Press the SET button to complete setting
Press the SET button with the current clock displayed. Then, the unit
setting is completed, and the unit changes to the Measuring screen.
SET
Register the setting
(Finish)
Display format
Hour Minute