Operating instructions, Main unit preparation – CatEye CC-VL200 [Velo 2] User Manual

Page 2

Advertising
background image

SET(on back)

Selects the flickering digits
Hour Minute Return to Measuring

Increases the figure

Rapidly increases the figure

O

do

A

v

T

m

D

st

SET(on back)

Moves to the next

Resets data

In display:
Clock Time Setting

In Odo display:

Wheel Circumference Setting

In display:

Enters power saving function

In Odo display:

No change

SET(on back)

Completes setting
Return to measuring

Increases the figure

Rapidly increases the figure

L

SET(on back)

Press simultaneously

Using the unit
for the first time

All Clear Operation

Press Main button and SET button simultaneously.

All displays illuminate, and then "Km" symbol flashes.

Speed Scale Selection

Press Main button and select "Km" or "Mile".

Wheel Circumference Setting

Increase the figure by Main button

(to increase rapidly, hold down the button).

Press SET button to fix it

Press SET button to fix it

Preparation Completed

Set the Clock time

After replacing
battery

Odo Data Input

Hold down Main button to

select Odo input display.

Input the figure by Main button

Press SET button to change the flickering digit.

MAIN UNIT PREPARATION

In Wheel Circumference
Setting Display:

In Clock TIme Setting Display

In Ordinary Display

All Clear Operation

Precautions

• Don't pay too much attention to your computer functions while riding. Keep your eyes on the

road and give due consideration to safe riding.

• Securely attach the magnet, sensor and bracket to your bicycle. Periodically check if the screws

and secure bands have loosend.

• Safely dispose of the old battery. Do not place it within children's reach. If swallowed by mistake,

consult a doctor immediately.

• Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit.
• For cleaning, use neutral detergent on soft cloth, and wipe off with dry cloth. Do not apply paint

thinner, benzine or alcohol, to avoid damages on the surface.

• If there is mud, sand or the like clogged between the button and the body, the movement of the

button may be deteriorated. Softly wash away such objects with water.

Spd

Current Speed

0.0(3.0) - 65mph

±

1 mph (under 31 mph) [0.0(4.0) - 105 km/h

±

1 km/h]

Aways displayed on the upper display and updated once a second.

Average Pace Arrow

Shows whether the current speed is faster or slower than the average speed

----- Faster than the average speed
----- Slower than the average speed

Odo

Total Distance (Odometer)

0.0 - 9999.9 mile[km]

±

0.1 mile[km]

Continuously measured until battery wears down. At 9999.9 km, it returns to zero
and counting begins anew. (With all clear operation, it return to zero; to continue
accumulation of data, input the previous Odo data after all clear operation.)

Dst

Trip Distance

0.00 - 999.99 mile[km]

±

0.01 mile[km]

The trip distance from start to current point is displayed. With reset operation, it
returns to zero.

Tm

Elapsed Time

0:00'00" - 9:59'59"

±

0.003 %

Elapsed time is measured from start to current point, in units of hours, minutes and
seconds. At 10 hours, it returns to zero and counting begins anew. With reset opera-
tion, it returns to zero.

Av

Average Speed

0.0 - 63.0 mph[99.9km/h]

±

0.3 mile[km]

The average speed from start to current point is displayed. If the elapsed time ex-
ceeds 10 hours, (.E) is displayed and calculation ceases.

Clock time

1:00' - 12:59' or 0:00' - 23:59'

±

0.003 %

If "Mile" is selected for scale symbol, the clock time is in 12 -hour. If "Km", the clock
time is 24-hour.

Power Saving Function

When the main unit does not receive a signal, or a button has not been pressed for
1~2 hours, the power supply is shut down and the main unit will only display the
clock

. By pressing the Main button, or by receiving signal, this function is re-

leased.

Trouble Shooting

No display.

Has the battery in the main unit worn out?
Replace it with a new one.

Incorrect data appears.

Do "All Clear" operation.(If possible, write down the Odo data before all clear operation, and
input it again after the display returns normal.)

Current speed does not appear. (When current speed does not appear, first short-circuit the
contact on the back with metal; if the speed display appears, the main unit is normal and the
problem must be in the bracket or the sensor.)

Is there anything on the contact of the main unit or of the bracket?
Wipe the contact clean.
Is the distance between the sensor and the magnet too far?
Are the marking line of the sensor and the center of magnet aligned?
Adjust the position of the sensor and magnet again.
Is the wire broken?
Replace it with a new one.

Current speed does not appear in wet condition.

Wipe the contacts with dry cloth. Contacts can also be treated with a water repellent silicon
jell from an automotive parts store or hardware store. Do not use industrial water repellent; it
may damage the bracket.

When "Mile" was chosen for speed scale,
the clock time is in 12-hour. If "Km", the clock
time is 24-hour.

How to Replace Battery

In order to continue accumulation of Odo data, write down the stored
Odo data before replacing the battery. Insert a new lithium battery
(CR2032) with the (+) pole upward.

Continuing Accumulation of Odo Data

Although the Odo data returns to zero by all clear operation, you can
continue accumulation of data by inputting the previous Odo data. Be
sure to write down the data before replacing the battery.

Measure the wheel
circumference by traveling
your bike on the ground for
one full wheel revolution. Or
"Selecting Values Cross
Reference Table" tells you an
approximate circumference
according to your tire size.

A. Speed Display
B. Mode Symbol
C. Average Pace Arrow
D. Speed Scale
E. Velocity Indicator
F. Sub-Display (Selected Function)
G. Main Button
H. SET Button
I. Battery Case Cover
J. Contact

Specifications

Applicable Wheel Circumference 112cm - 255cm (initial figure: 205 cm)
The length of the wire

70cm

Power Supply

Lithium Battery (CR2032) x 1

Battery Life

Approx. 3 years(The life of the first factory-loaded battery may be shorter than this
period.)

Dimension/Weight

1-25/32” x 1-9/16” x 5/8” [45 x 40 x 15.5 mm ] / 0.88oz. [25 g]

* The specifications and design are subject to change without notice.

1

Bracket

2

Wire

3

Sensor

4

Magnet

5

Rubber Pad

6

Nylon Ties

When you start/stop riding, the unit automatically starts/
stops measuring.
While measuring, the Velocity Indicator rotates.

HOW TO INSTALL

nylon tie

magnet

spoke

sensor

sensor's
marking
line

magnet's
center

front fork

brake cable

wire

nylon ties

bracket

rubber pad

handlebar

lever

Aline the magnet’s center
and the sensor’s marking
line. Make sure of 2mm
clearance between the
magnet and sensor. Tem-
porality attach the sensor to
the fork with the self-adhe-
sive patch.

Test

Slide the main unit onto the bracket
according to “How to Attach Main
Unit to Bracket” (below). Spin the
front wheel and check if the velocity
indicator is spinning. (If not, adjust
the relative positions of the magnet
and sensor again.) After the test, re-
move the main unit.

Fix the sensor with the nylon ties.

Note: Fasten the ties securely.

Secure the wire along the fork
with the nylon ties, and wind it
round the brake cable up to the
handlebar.

Note: Allow enough wire length

in the area marked with

in the illustration, to

insure full movement and
unhindered operation of
the handlebar.

Slide the main

unit onto the

bracket from front until

it clicks into position. To

remove it, pull it off forward

while pushing down the lever.

Just press Hold down

Button Operation

pull

clearance 2mm

open

close

slide

How to Attach Main Unit to Bracket

2

3

4

5

1

OPERATING INSTRUCTIONS

E

Advertising