CatEye CC-CD100N [Astrale] - Manual (Page 3)

R
1
2
3
4
5
6
7
1 2
3 4
1
2
3
Wheel Sensor/Magnet Mounting
Wire Clip
Mounting To Bike
CYCLOCOMPUTER
MODEL CC-CD100
CCMCD1-970210 0687281 5A
Lever
Wire Clip
Wire
Securing Tape
Wire Clip
Screw Cap
Wire
Outer Cable
Screw
Bracket
Cadence Sensor
Center of Magnet
Screw
Wire Securing
Tape
Cadence Sensor
Cadence Magnet
approx. 1mm
Cadence Magnet
Cadence Sensor
Center of Magnet
Wire
Slide
Front
Cadence Sensor/Magnet Mounting
(1) Securely fasten the ca-
dence magnet on the in-
side of the left crank with
the adhesive tape and
wire clip. (Fig.1)
(2) Attach the Cadence Sen-
sor to the front area of the
left chain stay by using
Sensor Band-A(L) & -
B(L), in the same proce-
dure as the Wheel Sensor
(Fig.2). Align the Center of
Magnet and Marking Line
of the Sensor, and make
s u r e o f a p p r o x . 1 m m
clearance between them
(Fig.3,4).
Wire Securing/Bracket Mounting
(1) Clamp the wire with the wire se-
curing tape and wire clip as
shown in Fig.1 &2. Wind the wire
around the outer cable to reach
the handlebar and adjust the
length. Loosen the wire in the
area marked with the arrow so
that the wire does not hinder
handlebar operation.
(2) Use either the 1mm or 2mm thick
rubber pad if necessary, accord-
ing to the handlebar diameter as
shown in Fig.3.
Main Unit Mounting
Mount the main unit onto the bracket by sliding it from front to
the rear until it clicks into position. When removing it, while
pushing the lever, slide it off forward.
Test
Mount the main unit on the bracket. Lift the rear wheel off the
ground and spin the wheel checking that Current Speed (S) is
displayed. Also, revolve the pedal to check that Cadence (C) is
displayed. If not, adjust positions of magnet and sensor follow-
ing the instruction on „Magnet Mounting„. Refer to the following
pages for the operation of the main unit.
(1)The spokes must run correctly through the
inside of the magnet as in Fig.1.
(2)Attach the Wheel Sensor to the rear area
of the left chain stay with Sensor Band-
A(S) & -B(S), following the instruction be-
low (Fig.4):
1.Insert the Band-B into the slit of the
Band-A, and put the Rubber Pad inside
of the Band-A (Fig.2). Adjust the length
in order that the screw-fastening part of
the Bands are parallel when mounted to
the chain stay (Fig.3).
*To pull out the Band- B from Band-A,
tug strongly.
2.Mount the adjusted Bands to the chain
stay along with the Wheel Sensor, by
temporarily tightening the screw (Fig.5).
Align the Center of Magnet and the
Sensor’s Marking Line, and make sure
of 1mm clearance between the Magnet
and Sensor (Fig.4,6). Then tighten the
screw securely. Cut the excess of the
Band-B with a nipper or the like.
*Figure 7 shows how to attach the wheel
magnet on ATB or MTB bikes, where
the gap between the chainstay and
spoke is extra wide. Attach the sensor
as close to the wheel magnet as pos-
sible, but don’t let them touch one an-
other.
Parallel
Screw
Wheel Magnet
Spoke
Sensor Band A
Sensor Band B
Rubber Pad
Sensor Band A
Sensor Band B
Rubber Pad
Center of Magnet
Wheel Sensor
Wheel Magnet
Wire Securing Tape
Screw
Wheel Sensor
Wheel Sensor
Wheel Magnet
approx. 1mm
Wheel Sensor