Fagor 6H-880ATCX - Manual (Page 32)

e n g l i s h
30
3.4 Autopyro. This function automatically
calculates the cleaning time depending on how
dirty the oven is. Select Cleaning on the menu
and validate (3.4.1). Select AUTO PYRO and
validate (3.4.2). (3.4.3) will appear. Validate.
The oven will begin to calculate the duration
according to how dirty it is. The door will be
blocked for safety reasons (3.4.4).
3.5 After pyrolysis (depending on model).
Take out the side runners and clean off
any grease or ash that has been left after
the cleaning processes. Depending on the
models, the side runners are fi xed in two
ways, either without a support (3.5.1, 3.5.2)
or with a support (3.5.4, 3.5.5). When you
have removed them, use a damp cloth to
clean the side walls (3.5.3, 3.5.6). When you
have cleaned the oven walls, replace the
runners. If your oven has a fold-down grill,
pull upwards and press to fold it down (3.5.7)
and clean the top wall with a damp cloth
(3.5.8).
3.6 Cleaning the glass
Cleaning the outside of the glass: Use a
soft cloth soaked in a glass cleaning product.
Cleaning the inside of the glass: If the
inside of the glass is dirty, you can remove it
for cleaning.
When the oven has cooled down, open the
door as wide as possible (3.6.1) and fi x it
in place with the red stop supplied in the
accessories bag (3.6.2). Use the remaining
sheet accessory on one side of the glass to
raise up the glass like a lever. Do the same
on the other side of the glass. Remove the
red stop and close the door (3.6.3). Remove
the glass (3.6.4), clean it and dry it with a cloth
(3.6.5). If necessary, remove the whole glass
panel unit inside the door. This unit consists of
either one or two glass panels, depending on
the model, with a black stop in each corner. To
remove them, place your hand under the door
and pull upwards (3.6.6). When you have taken
out the unit, remove the stops to clean the
glass panels (3.6.7).
When the glass panels are clean (3.6.8) fi t them
onto the rubber stops again, with the stud
facing upwards (3.6.9) and replace the glass
panels so that the letters “L” (left) and “R” (right)
are beside the hinges (3.6.10). Lastly, place
the remaining glass panel so that the word
PYROLYTIC can be read (3.6.11). Remove the
stops (3.6.12) and close the door.
3
Maintenance and
cleaning
3.1 Cleaning the accessories. The accessories
are dishwasher-safe. To wash them up by
hand, use ordinary detergent. Leave them to
soak for easier cleaning.
3.2 Pyrolysis cleaning
• The cleaning process consists of the dirt
being burnt at high temperatures.
• The smoke and smells are eliminated by a
catalyser.
• There is no need to wait until the oven has
accumulated a large amount of grease to
perform the cleaning process.
• After pyrolysis, when the oven has cooled
down, wipe it with a damp cloth to remove
the white ash residue.
• Before starting the pyrolysis process,
take all the accessories out of the oven,
including the cooking accessories and the
telescopic runners.
• If any substances are stuck to the inside of
the oven due to spill-overs, remove them
before carrying out the pyrolysis process
as they could catch fi re or give off large
amounts of smoke.
• During the pyrolysis process the surfaces
become hotter than during normal use.
Keep children away from the oven.
3.3 Pyro-turbo. This process takes two hours
and guarantees thorough, intense cleaning
of the inside of the oven. Select Cleaning on
the menu and validate (3.3.1). Select PYRO
TURBO and validate (3.3.2). (3.3.3) will appear.
Validate. The door will be locked for safety
reasons (3.3.4) and the pyrolysis process will
begin. When the cleaning process is complete,
(3.3.5) will appear. When the door is unlocked,
the oven will indicate that the cleaning process
is complete.
You may change the end of cleaning time if you
wish. Press
, select Change and validate
(3.3.6). Select , change the end of cleaning
time and validate (3.3.7). will appear on
the main display to indicate that the oven is
programmed (3.3.8).
Notes: The temperature and time parameters
are set parameters and cannot be changed.
The enamelled tray can be cleaned with this
pyrolysis option. Firstly remove any excess
grease from the tray and then place it at level 2.