Unpacking your t-glide fence system, Sawstop – SawStop T-Glide Fence System User Manual

Page 3

Advertising

Unpacking Your T-Glide Fence System

While unpacking your saw, verify that you have all the components shown below for your specific fence

system. The T-Glide Fence System – Professional Series is available in either a 52” system or a 36” system. The

components pictured below are from the 52” system, although the components from the 36” system are similar.

front tube

front rail

rear rail

extension table

installation instructions poster

owner’s manual

SawStop

OWNER’S MANUAL

T-Glide

Fence System-

Professional Series

(four for 52” system,

two for 36” system)

angle bracket

fence handle

T-Glide table

hardware pack

Countersunk Socket

Head Bolts, M8 x 25 (6)

Washers,

M8.5 x 23 (6) 19

Lock Washers,

M8 (6)

Philips Head Screws,

M4 x 16 (12)

Foot,

(2)

Hex Head Bolts,

M10 x 45 (4) 15

Hex Nuts,

M8 (8) 14

Nylon Lock Nuts,

M10 (4)

T-Glide 52” Table Hardware Pack

T-Glide rails

hardware pack

T-Glide Rails Hardware Pack

Countersunk Socket Head Bolts,

M8 x 25 (8)

Lock Washers,

M8 (8)

Hex Nuts,

M8 (8)

Hex Head Screws with Attached

Washers, M8 x 16 (9)

Washers,

M8.5 x 23 (8) 2

Countersunk Socket

Head Screws, M8 x 16 (4) 5

SawStop

T-Glide fence

Assembling Your T-Glide Fence System

SawStop Service Department

503-682-6222

www.sawstop.com

Before assembling your T-Glide fence system,

make sure that you have all the necessary

components identified on page 1 in the Owner’s

Manual, including the two hardware packs. Call the

SawStop Service Department at 503-682-6222 if

any components are missing. You will also need the

following tools to complete the fence installation:

1. a 5 mm hex key

2. a 13 mm wrench

3. two 17 mm wrenches (or adjustable wrenches)

4. a Phillips head screwdriver

5. a level or straight-edge

Note: The drawings in the installation poster

illustrate the T-Glide rails and extension table for

the 52” system. The instructions for assembling

and using the 36” system are the same.

Flip to

Other Side

30
SawStop

10” Contracto

r Saw

SawStop

System Status Code

Status

Red

Grn

¯¯¯

Wet Wood

Overload Due To

During Bypass

Contact Detected

During Standby

Contact Detected

Brake

Adjust Position of

Doors

Close Access

Key To “On”

Turn Cartridge

To “Off”

Turn Star t Switch

Bypass Mode On

Coasting Down

Replace Cartridge

System Ready

System Initializing

• • • • • •

¯¯¯

• • • • • •

¯¯¯

• • • • • •

¯¯¯

• • • • • •

SawStop

10” Contractor Saw

Made in T

aiwan

SawS

top, LLC ww

w.sawst

op.c

TCP

10¨ Con

tractor S

SawStop

Model No.

CNS 17

Serial No. C

4012345

Electrical / El

ect

ricidad / Él

ect

ricité

115/230 Vol

ts, 6

0 Hz

15/7.5 Amp

1 Phase

1.75 HP

3500 RPM

175370

Mov

ing

belt

s and

part

can

pinc

h, cu

t or

crus

Do n

ot o

pera

te w

ith

belt

gua

rd o

pen.

Made in Taiwan

SawS

top, LL

www.

sawstop.com TCP

10¨ Contractor Saw

SawStop ®
Model N

o. CNS 175

Serial No. C0

74012345

Electrical / Electricidad / É

lectricité

115/230 Vo

lts, 60 Hz

15/7.5 Amps

1 Phase

1.75 HP

3500 RPM

cUS

1753

Moving

belts a

nd par

can pin

ch, cut

or crus

Do not

operat

e with

belt gu

ard op

en.

SawStop, the

SawStop blad

e logo, and

the

configuration oft

his product

are either regi

stered

trademarks or

trad

emarks of Sa

wStop, LLC.

Software copyr

ight 2

003-2006 by S

awStop, LLC.

All rights reser

ved. Protected

by one or mor

e of

the following U

.S. patents 6

813983, 6826

988,

6857345,68774

10, 6880440,

6920814, 6945

148,

6945149,69576

01, 6994004, 6

7090, 7000514

7024975,70554

17, 7077039,

7098800, 7100

483,

7137326,71718

79, 7197969, 7

0383, 7225712

7228772, 7231

856 and Ta

iwan patent 143

466.

Additional U.S.a

nd foreign pate

nts pending.

WARNING

Do not remov

e the dust sh

roud because

the blade will b

e exposed. If

you contact the

blade under th

e table, the bla

de may retrac

toward you an

d cause a s

evere injury.

front rail

level the top of

the front rail with

the lower edge

of the bevel

straight-edge

rear rail

straight-edge

support

leg

• Locate the front rail, the rear rail, and the T-Glide rails hardware

pack. All of the hardware needed to install the rails is located on

the T-Glide rails hardware pack and is shipped in the T-Glide

fence box. In order to easily identify the hardware used in each

of the following steps, the different pieces of hardware are

numbered on the hardware pack and in the figures.

• Align the front rail (the larger of the two rails) with the front edge

of the table top so the cut-outs at the top of the rail are centered

on the miter gauge slots in the table and so the holes in the rail

align with the holes along the front edge of the table and

extension wings. Remove six M8 x 25 countersunk socket

head bolts from the T-Glide rails hardware pack and insert

one through each of the holes in the rail and table.

• Place an M8.5 x 23 washer and an M8 lock washer

on the back of each of the six M8 x 25 countersunk

socket head bolts , and then thread an M8 hex nut on

each bolt. Hand tighten the nuts; do not fully tighten them.

• The holes in the front edge of the table and extension wings are

slightly larger than the bolts they receive to allow you to level the

front rail and extension wings to the table top. Align the top of

the front rail with the lower edge of the bevel on the front edge

of the table top. Use a 5 mm hex key and a 13 mm wrench to

fully tighten the nuts on the back of the four bolts that extend

through the table top. Do not tighten the nuts on the bolts that

extend through the extension wings.

bevel

tighten

level the extension

wing and tighten the

nut on this bolt

• Use a straight-edge to level the front edge of the left extension

wing to the cast iron table top. You may have to pull up or push

down on the outer edge of the extension wing to level it. Once

the front edge of the left extension wing is level, use a 5 mm hex

key and a 13 mm wrench to fully tighten the nut on the bolt that

mounts the left extension wing to the front rail. Repeat this

process to level the front edge of the right extension wing.

• Align the rear rail (the smaller of the two rails) with the rear

edge of the table top so the cut-outs at the top of the rail are

centered on the miter gauge slots in the table and so the holes

in the rail align with the holes along the back edge of the table

and extension wings. Notice that the holes in the table are

threaded but the holes in the extension wings are not. Remove

four M8 x 16 countersunk socket head screws from the

T-Glide rails hardware pack and thread one through each of the

holes in the rail and into the threaded holes in the table.

Tighten the four screws using a 5 mm hex key.

• Take two M8 x 25 countersunk socket head bolts and insert

one through each hole in each extension wing. Place an

M8.5 x 23 washer and an M8 lock washer on the

back of each bolt and then thread an M8 hex nut on

each bolt. Hand tighten the nuts; do not fully tighten them.

• Use a straight-edge to level the rear edge of the left extension

wing to the cast iron table top. You may have to pull up or push

down on the outer edge of the extension wing to level it. Once

the rear edge of the left extension wing is level, use a 5 mm hex

key and a 13 mm wrench to fully tighten the nut on the bolt that

mounts the left extension wing to the rear rail. Repeat this

process to level the rear edge of the right extension wing.

level the extension

wing and tighten the

nut on this bolt

• Once the rails are in place you can mount the extension table to

the rails, but first you must mount the support leg or legs to the

extension table. The extension table for the 36” fence system has

one support leg and the extension table for the 52” fence system

has two. Locate the support legs, the angle brackets, and the

T-Glide table hardware pack. Begin by installing the adjustable

foot in the bottom of each support leg. Thread an M8 nut onto

the threaded shaft of the foot as close to the rubber base as

possible, and then thread the foot into the bottom of the support

leg as far as possible.

• Each support leg is mounted to the underside of the extension

table using two angle brackets. Align the two holes in the

support leg to the two holes in the brackets. Put one of the

M10 x 45 hex head bolts through each hole in the leg and

brackets. Thread an M10 nylon lock nut on each bolt and

tighten with a 17 mm wrench. You will need to hold the head of

the hex bolt with another 17 mm wrench to tighten the lock nut.

Do not fully tighten the nuts; leave them just loose enough to be

able to move the brackets.

angle bracket

• Mount the angle brackets to the underside of the extension

table using three M4 x 16 Phillips head screws per bracket.

The underside of the extension table is pre-drilled to receive the

screws. Be careful not to overtighten the screws because you

may strip the threads in the wood. Once all the brackets

have been mounted to the table, fully tighten the

M10 nylon lock nuts that secure the legs to the brackets.

T-Glide Rails Hardware Pack

Countersunk Socket Head Bolts,

M8 x 25 (8)

Lock Washers,

M8 (8)

Hex Nuts,

M8 (8)

Hex Head Screws with Attached

Washers, M8 x 16 (9)

Washers,

M8.5 x 23 (8) 2

Countersunk Socket

Head Screws, M8 x 16 (4) 5

Countersunk Socket

Head Bolts, M8 x 25 (6)

Washers,

M8.5 x 23 (6) 19

Lock Washers,

M8 (6)

Philips Head Screws,

M4 x 16 (12)

Foot,

(2)

Hex Head Bolts,

M10 x 45 (4) 15

Hex Nuts,

M8 (8) 14

Nylon Lock Nuts,

M10 (4)

T-Glide 52” Table Hardware Pack

support leg

(two for 52” system,

one for 36” system)

SawStop T-Glide Fence System - Professional Series 1

Advertising

Popular Brands

Popular manuals