RADWAG WPW 60/H5/K Multifunctional Scales - Manual (Page 5)

- 5 -
22.5.1. acklight – power supply from mains ................................................................................91 B
2 .5.2. Backlight - power supply from the accumulator ................................................................92 2
22.6. Beep” sound – key-press reaction ..............................................................................................92 “
22.7. eypad modes.............................................................................................................................93 K
22.8. Software version view ..................................................................................................................94
23. SCAL CALIBRATION .........................................................................................................................94 E
23.1. alibration procedure ..................................................................................................................95 C
23.2. Start mass adjustment .................................................................................................................96
24. WORK MODES .....................................................................................................................................97
24.1. ccessibility of work modes .........................................................................................................97 A
24.2. rogrammable keys.....................................................................................................................98 P
24.3. /- control according to an inscribed standard mass..................................................................100 +
24.4. aximal force latch....................................................................................................................102 M
24.5. Counting pieces.........................................................................................................................102
24.5.1. nabling work modes ......................................................................................................103 E
24.5.2. etting standard mass by inscribing the mass of a single piece ....................................103 S
2 .5.3. Setting the standard mass by declaring the quantity of a sample ....................................104 4
24.6. Deviation in percents in relation to a standard mass..................................................................105
24.6.1. tarting weighing in per cents..........................................................................................105 S
24.6.2. eighing a standard mass ..............................................................................................105 W
2 .6.3. Inscribing a standard mass..............................................................................................106 4
24.7. Weighing animals ......................................................................................................................107
24.7.1. eighing time setting ......................................................................................................107 W
24.7.2. tarting the work mode....................................................................................................108 S
2 .7.3. Procedure of weighing animals........................................................................................108 4
24.8. Recipes – filling/dosing ..............................................................................................................109
24.8.1. ecipe multiplier ..............................................................................................................109 R
24.8.2. etting tare in the filling/dosing mode ..............................................................................110 S
24.8.3. anual confirmation of every ingredient ..........................................................................110 M
24.8.4. umber of cycles declaration ..........................................................................................111 N
24.8.5. hute time delay..............................................................................................................112 C
24.8.6. utomatic printout of report .............................................................................................112 A
24.8.7. egative dosing ...............................................................................................................113 N
24.8.8. roduct series number.....................................................................................................114 P
24.8.9. Additional product............................................................................................................115
24.8.10. ork mode setting ........................................................................................................116 W
24.8.11. Process of dosing / filling...............................................................................................117
25. IAGRAMS OF CONNECTION CABLES ...........................................................................................119 D
26. CONNECTORS ...................................................................................................................................121
26.1. IN/3OUT connector..................................................................................................................121 3
26.2. RS232, RS485 connector ..........................................................................................................122
27. SPECIFICATION OF ADDITIONAL MODULES..................................................................................123
27.1. Ethernet module - ET.................................................................................................................124
27.1.1. ounting way in PUE C41H ............................................................................................125 M
2 .1.2. Drawings of sockets and cables for Ethernet...................................................................127 7
27.2. Analogue output module............................................................................................................127
27.2.1. echnical specification ....................................................................................................128 T
27.2.2. he way of installing inside PUE C41H...........................................................................128 T
27.2.3. onfiguration of work modes of analogue modules .........................................................129 C
2 .2.4. Connections to AN module ..............................................................................................130 7
27.3. Relay odule - PK1...................................................................................................................131 m
27.3.1. echnical specification ....................................................................................................131 T
27.3.2. nstalling in PUE C41H indicators ....................................................................................131 I
2 .3.3. Drawing of cables and outputs ........................................................................................133 7
27.4. WE 4 - 4 inputs / 4 outputs module............................................................................................133
27.4.1. echnical specification ....................................................................................................133 T
27.4.2. olours of cables for I/O ..................................................................................................134 C
2 .4.3. Installing method in PUE C41H indicators .......................................................................134 7
27.5. WE 8 - 8 inputs / 8 outputs module............................................................................................135
27.5.1. echnical specification ....................................................................................................136 T
27.5.2. Installing method in PUE C41H indicators .......................................................................136