Sharp GX-M10HOR - Manual (Page 54)

12/10/26 12_GX-M10H_OM_EN.fm
E-19
Timer and sleep operation (Remote control only)
Timer playback:
The unit turns on and plays the desired source (CD,
TUNER, USB, iPod, AUDIO IN) at a preset time.
This unit has 2 types of timer: ONCE TIMER and DAILY
TIMER.
Once timer:
Once timer play works for one time only at a preset time.
(“
” indicator).
Daily timer:
Daily timer play works at the same preset time every day. For
example, set the timer as a wake-up call every morning.
(“DAILY” indicator).
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio
programme, and use the daily timer to wake up.
Notes:
● When performing timer playback using another unit
connected to the USB/iPad terminal or AUDIO IN
socket, select “USB” or “AUDIO IN” in step 5. However,
if the source is set to USB, make sure there is no iPod
or iPhone docked to the unit.
● This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn
on or off. To stop the timer playback, follow step
“Cancelling the timer setting” of this page.
Checking the timer setting:
Cancelling the timer setting:
1 Set the daily timer (pages 19 - 20).
2 Set the once timer (pages 19 - 20).
■ Timer playback
Before setting timer:
● Check that the clock is set to the correct time (refer to
page 6). If it is not set, you cannot use the timer
function.
● For timer playback: Plug in USB or load discs or dock
iPod to be played.
1 Press the ON/STAND-BY button to turn the power on.
2 Press and hold the CLOCK/TIMER button.
3 Within 10 seconds, press the or button to
select “ONCE” or “DAILY”, and press the ENTER
button.
4 Within 10 seconds, press the or button to
select “TIM.SET”, and press the ENTER button.
5 To select the timer playback source (CD, TUNER, USB, iPod,
AUDIO IN), press the or button.
When you select the tuner, select a station by pressing the
or button, and then press the ENTER button.
If a station has not been programmed, “NOPRESET” will be
displayed and timer setting will be cancelled.
Once timer Daily timer
Start Stop
1 minute or more
Start Stop
6 Press the ENTER button to adjust the hour. Press the
or button and then press the ENTER
button.
7 To adjust the minutes, press the or
button and then press the ENTER button.
8 Set the time to finish as in steps 6 and 7 above.
9 Adjust the volume using the VOLUME control, and then
press the ENTER button. Do not turn the volume up too
high.
10 Press the ON/STAND-BY button to enter the power
stand-by mode. The “TIMER” indicator lights up and
the unit is ready for timer playback.
11 When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the
preset volume. The timer indicator will blink during
timer playback.
12 When the timer end time is reached, the system will
enter the power stand-by mode automatically.
Once timer:
The timer will be cancelled.
Daily timer:
The timer operates at the same time every selected day.
It will continue until the daily timer setting is cancelled.
Cancel the daily timer when it is not in use.
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
2 Within 10 seconds, press the or button to
select “ONCE” or “DAILY”, and press the ENTER button.
3 Within 10 seconds, press the or button to
select “TIM.CALL”, and press the ENTER button.
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
2 Within 10 seconds, press the or button to
select “ONCE” or “DAILY”, and press the ENTER button.
3 Within 10 seconds, press the or button to
select “TIM.OFF”, and press the ENTER button. Timer
will be cancelled (the setting will not be cancelled).
REMOTE SENSOR
TIMER