Sharp GX-M10HOR - Manual (Page 56)

12/10/26 12_GX-M10H_OM_EN.fm
E-21
Troubleshooting chart (continued)
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter on
the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no
disc in the unit until normal playback is possible (about 1
hour). Wipe off any condensation on the transmitter with a
soft cloth before operating the unit.
When this product is subjected to strong external
interference (mechanical shock, excessive static
electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on
again.
2 If the unit is not restored in the previous operation,
unplug and plug in the unit again, and then turn the
power on.
Note:
If neither operation above restores the unit, clear all the
memory by resetting it.
Caution:
This operation will erase all data stored in memory
including clock, timer settings and tuner preset.
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
● Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not
mark this surface.
● Keep your discs away from direct sunlight, heat, and
excessive moisture.
● Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a
CD is dirty or does not play properly, clean it with a soft,
dry cloth, wiping straight out from the centre, along the
radius.
Maintenance
Periodically wipe the cabinet with a soft cloth and a diluted
soap solution, then with a dry cloth.
Caution:
● Do not use chemicals for cleaning (petrol, paint thinner,
etc.). It may damage the cabinet.
● Do not apply oil to the inside of the unit. It may cause
malfunctions.
■ USB
Symptom Possible cause
● Device cannot be
detected.
● There is no MP3/WMA file
inside the device.
● The device is not properly
connected.
● A MTP device is connected.
● The device contains AAC
file only.
● Playback does not
start.
● A copyright-protected WMA
or false MP3 file is being
played back.
● Wrong time display.
● Wrong file name
display.
● A Variable Bitrate files are
being played back.
● The File Name was written
in other than English
characters.
■ iPod, iPhone or iPad
Symptom Possible cause
● No sound is
produced.
No image appears
on the TV/monitor.
● The iPod, iPhone or iPad is
not playing.
● The iPod, iPhone or iPad is
not properly connected to
the unit.
● The AC power lead of the
unit is not plugged in.
● The video cable is not
properly connected.
● The TV/monitor’s input
selection is not properly set.
● The iPod TV out feature has
not been set to output video.
● USB/iPad terminal do not
support video.
● iPod, iPhone or
iPad will not
charge.
● The iPod, iPhone or iPad is
not making full contact with
the connector.
● Using iPod (3 rd generation).
● The iPod or iPhone is not
supported. Refer to page 7
for compatible models.
● “This accessory is
not made to work
with iPhone” or
“This accessory is
not supported by
iPhone” appears on
iPhone screen.
● The iPhone battery is low.
Please charge the iPhone.
● iPhone is not properly
docked.
■ Condensation
■ If problem occurs
■ Factory reset, clearing all memory
1 Press the ON/STAND-BY button to enter the power
stand-by mode.
2 Whilst pressing down the VOLUME + button, press the
ON/STAND-BY button until “RESET” appears.
■ Care of compact discs
■ Cleaning the cabinet
NO YES
Correct