Neff B45C52N3GB - Manual (Page 11)

11
Filling and emptying the water tank
:
Risk of injury and risk of fire!
Only fill the water tank with water or with the descaling solution
that is recommended by us.
Do not pour any flammable liquids (e.g. alcoholic drinks) into
the water tank.
Due to hot surfaces, vapours from flammable liquids may catch
fire in the cooking compartment (explosion). The appliance
door may spring open. Hot steam and jets of flame may
escape.
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
Notes
■
If you use mineral water, set the water hardness to hard.
■
For hygiene reasons, a reminder message will appear after
the appliance is switched off if the water tank has not been
emptied. The reminder message goes out once the water
tank is empty.
Filling the water tank
Fill the water tank before each use with steam assistance.
1. Press lightly on the centre of the lower edge of the water tank
(picture A).
2. Pull out the water tank (picture B).
3. Fill the water tank with cold water up to the "max" mark
(picture C).
4. Slide in the water tank all the way.
Note: If the Î symbol flashes, the water tank has not been
pushed in fully.
Topping up the water tank
If the water tank is empty, a signal sounds and the
Î symbol
lights up. Steam-assisted operation is interrupted.
1. Pull out the water tank.
2. Fill the water tank up to the "max" mark and slide it in fully.
The steam-assisted operation continues.
Emptying the water tank
Empty the water tank after each steam-assisted use of the
appliance.
1. Turn the operating mode selector back to the Û off position
and push it in.
The remaining water in the evaporator system is pumped
back into the water tank. The Ì symbol lights up. ˜ž©
appears in the temperature display. (pumping-out). When the
pumping out cycle is complete, a signal sounds and the Î
symbol flashes.
2. Pull out the water tank slowly and level.
The
Î symbol goes out.
3. Remove the cover (Picture A).
4. Empty the water tank (Picture B).
5. Dry the tank shaft and water tank thoroughly.
6. Slide in the water tank.
The
Î symbol and the ˜ž© display (pumping-out) go out.
Switching off the appliance
:
Risk of scalding!
When opening the appliance door, hot steam may escape.
After cooking, only open the appliance door carefully.
Note: The appliance has a cooling fan. After the appliance is
switched off, the cooling fan may continue to run.
1. Turn the operating mode selector back to the off position Û .
2. Press on the operating mode selector until it retracts.
The appliance switches off. The
~ symbol goes out.
Note: If the appliance is switched off after steam-assisted
operation, you will hear a pumping sound. The appliance is
pumping the remaining water out of the evaporator system
back into the water tank. During this time the Ì symbol is lit.
Only empty the water tank when the Ì symbol is no longer lit.
You can see in the temperature display whether there is high or
low residual heat in the cooking compartment.
Ending an operation
Press and hold the „ Stop button. The appliance turns off the
current operation. The appliance is not switched off. You can
now start another operating mode.
Interrupting and continuing an operation (Pause)
Briefly press the „ Stop button. The appliance interrupts the
current operation. Press the ƒ Start button to continue the
operation.
$ %
&
Temperature dis-
play
Meaning
• Residual heat high (above 120 °C)
œ Residual heat low (between
60 °C and 120 °C)
$ %