JLG 450AJ ANSI Operator Manual - Manual (Page 43)

SECTION 3 - USER RESPONSIBILITIES AND MACHINE CONTROL
3120748 – JLG Lift – 3-13
DANGER !
ELECTROCUTION HAZARD
Death or serious injury will occur from contact
or being too close to electrical lines.
This machine is not insulated.
Maintain a clearance of at least 10 ft. between any part of machine
or load and any electrical line or apparatus charged up to 50,000 volts.
One foot additional clearance is required for each additional 30,000
volts or less.
Allowances must be made for operator error, machine deflection and
electrical line swaying.
1703805 A
1703805 A
1703804 A
WARNING !
CRUSHING HAZARD
Failure to follow these instructions could
result in death or serious injury.
Do not stand under a raised platform or boom,
or between a rotating platform and the boom.
Keep all body parts away from any moving components.
1703804 A
1703804 A
WARNING !
CRUSHING HAZARD
Failure to follow these instructions could
result in death or serious injury.
Do not stand under a raised platform or boom,
or between a rotating platform and the boom.
Keep all body parts away from any moving components.
1703804 A
1703804 A
WARNING !
CRUSHING HAZARD
Failure to follow these instructions could
result in death or serious injury.
Do not stand under a raised platform or boom,
or between a rotating platform and the boom.
Keep all body parts away from any moving components.
1703804 A
DOM 1703797
WARNING !
DANGER !
THIS MACHINE MUST NOT BE USED UNTIL IT IS INSPECTED AND OPERATING PROPERLY.
DO NOT operate this machine unless you have been properly trained as
described in the JLG Operation and Safety Manual by a qualified person
and authorized to operate this machine. Your training includes reading
and understanding the safety, operating and maintenance instructions in
manufacturer’s manuals, knowing your employers work rules and
applicable governmental regulations.
Follow the instructions in the Operating Manual and sections 6, 7 and 8 of
ANSI A92.5-1992 for daily, frequent and annual inspections. These may
be obtained from your authorized JLG Industries, Inc. equipment dealer
or JLG Industries, Inc.
DO NOT replace items (i.e., batteries, tires, counterweight, etc.) with
items of different weight or specification because this will affect the
stability of the machine.
DO NOT modify or change this machine without written approval from
the manufacturer.
Operate this machine with extreme caution. STOP all operation if a
malfunction occurs.
Test foot switch for proper operation.
Test high engine and high drive cut out switches for proper operation.
Improper use of this machine could cause death
or serious injury.
TIP-OVER HAZARD
Machine must be on a smooth, firm and level surface before swinging, elevating and/or
extending boom.
DO NOT exceed platform rated capacity.
Make sure the operating surface will support the machine.
DO NOT drive with platform raised, or raise platform, when on uneven, sloping or soft surfaces
including trucks, trailers, railway cars, floating vessels, scaffolds or similar areas.
DO NOT raise platform during high winds.
DO NOT drive near drop offs, holes or other hazards.
Make sure all tires are in good condition and air filled tires are properly inflated.
To drive on a slope, boom must be retracted, lowered below horizontal and centered between
the rear wheels.
When “Chassis out of level” indicator light is on, retract and lower boom and move machine
to a level surface.
Driving with boom above horizontal or extended is restricted to smooth, firm and level surfaces
free of obstructions.
Death or serious injury could result from a tip-over.
CRUSHING HAZARD
Always look in the direction of movement.
Keep clear of obstructions.
Direction of drive and steer functions are opposite to the motion of the controls
when the platform is positioned over the front axle end. Always look at the decals
on the chassis and drive / steer control for proper direction.
Keep all body parts inside of platform during operation.
Failure to follow instructions could result in death or serious injury.
Falling from platform could cause death or serious injury.
FALLING HAZARD
Check the condition of the approved fall protection device, lanyard and the
designated attachment point to the platform.
Wear approved fall protection items and attach to marked locations.
Keep both feet on platform floor.
Ensure entrance area is properly closed.
DO NOT use planks, ladders or similar items in platform to get added reach.
ELECTROCUTION HAZARD
Death or serious injury will occur from contact or being too close to electrical lines.
This machine is not insulated.
Maintain a clearance of at least 10 ft. between any part of machine or load and any electrical line or apparatus charged up to 50,000 volts.
One foot additional clearance is required for each additional 30,000 volts or less.
Allowances must be made for operator error, machine deflection and electrical line swaying.
1703797
WARNING !
WARNING !
DANGER !
DO NOT replace items (i.e., Batteries, tires, counterweight, etc) with items of different weight
or specification because this will affect the stability of the machine.
DO NOT modify or change this machine without written approval from the manufacturer.
Read and understand decals and placards.
Check all functions at ground control and platform control stations. Select an area free of obstructions.
Refer to the JLG Operation and Safety Manual for further daily/ frequent/ annual checks and the walk around inspection.
Make sure all tires are in good condition and air filled tires are properly inflated.
Operate this machine with extreme caution. STOP all operation if a malfunction occurs.
If this machine is not properly maintained, death or serious injury could occur. DOM 1703798
THIS MACHINE MUST NOT BE USED UNTIL IT IS
INSPECTED AND OPERATING PROPERLY.
CRUSHING HAZARD
Failure to follow these instructions could
result in death or serious injury.
ELECTROCUTION HAZARD
This machine is not insulated.
Maintain a clearance of at least 10 ft. between any part of machine
or load and any electrical line or apparatus charged up to 50,000 volts.
One foot additional clearance is required for each additional 30,000
volts or less.
Allowances must be made for operator error, machine deflection and
electrical line swaying.
Death or serious injury will occur from contact or being
too close to electrical lines.
DO NOT operate this machine unless you have been properly trained as described in the JLG Operation and Safety
Manual by a qualified person and authorized to operate this machine. Your training includes reading and understanding
the safety, operating and maintenance instructions in manufacturer’s manuals, knowing your employers work rules and
applicable governmental regulations.
Personnel shall not position themselves or other objects UNDER boom
and platform or BETWEEN boom and turntable or chassis.
When operating from ground control station avoid being BETWEEN
rotating superstructure and chassis or other immovable objects.
1703798
Figure 3-7. Danger and Warning Decal Location