Blue Sea Systems 3119 SMS Surface Mount System - Manual (Page 2)

Gland Specifications
Gland Specifications
WIRE SIZE
.230 in
5.8 mm
.530 in
13.9 mm
.114 in
2.9 mm
.250 in
6.4 mm
Min. Dia. Max. Dia.
#6
Cable,
4 Conductor
.590 in
15.0 mm
.990 in
25.4 mm
A. Clearance Hole
1.470 in (37.3 mm)
B. Max. O. A. Length
2.23 in (56.6 mm)
C. Wrenching Flats
1.66 in (42.2 mm)
Reference diagram below
A. Clearance Hole
.886 in (22.5 mm)
B. Max. O. A. Length
1.66 in (42.2 mm)
C. Wrenching Flats
1.05 in (26.7 mm)
Reference diagram below
A. Clearance Hole
.492 in (12.5 mm)
B. Max. O. A. Length
1.17 in (29.7 mm)
C. Wrenching Flats
.59 in (15.0 mm)
Reference diagram below
#14 to
#10
Cable,
3 Conductor
#14 to
#10
Single
Wire
CABLE DIA. RANGE DIMENSIONS
Small 3124 (PG7)
Large 3126 (PG29)
Medium 3125 (PG16)
C
B
SEALING NUT
A
SUGGESTED CLEARANCE HOLE
FOR NONTHREADED MOUNTING
Required Tools
• Hole Saw, drill or step drill suitable for cable glands (see information on back).
• Drill motor suitable for above
• Screw Drivers
• Knife
• Measuring device
• Wire cutters and Crimpers
Required Parts
• Suitable ring terminals for circuit breaker and grounding connections
• In some installations it may be desirable to attach a mounting substrate to the
hull with adhesive or epoxy instead of screwing directly to the hull.
Installing the Enclosure Panel
• The Surface Mount System Enclosure Panel should be installed by a certified
marine electrician.
• Plan the installation by determining where the enclosure will be mounted
o Per ABYC, the enclosure cannot be mounted further than the reach of a 10'
cable from the AC power inlet
o Consider the needed clearances to access the enclosure and open the sealed cover
o Allow for a wire drip loop outside the enclosure and sufficient service loop
for wires inside the enclosure
• Determine which included glands are needed. It is recommended that glands be
installed on the bottom of the enclosure to maintain the waterproof integrity of
the sealed enclosure.
• Smaller glands may permit convenient installation of a galvanic isolator if used
in the systems. In this case the line safety ground wire would exit the enclosure
to the galvanic isolator and the boat side of the galvanic isolator would return to
the enclosure to join the internal connections and the ground from the load side
power cable.
• Try all cable glands on the wire for correct fit before proceeding.
• Flat cables can be manipulated to a nearly round shape to fit and seal better
in the gland.
• Large round cables with #6 Wire may be a very tight fit in the cable gland.
Dismantle the gland and use wire lubricant to ease cable through the rubber
seal if necessary.
• When drilling holes for cable glands, be sure to allow sufficient clearance inside
for the nut. The best location is as close to the back of the enclosure as
possible and still allow for the nut.
Installation Components Included
KEY
3113 SMS Panel Enclosure Includes:
6 blank circuit positions
6 LED plugs
12 circuit breaker mounting screws
30 Basic DC labels, 4205
30 Basic AC labels, 4206
Panel Voltage ID labels
12V DC, 24V DC
120V AC, 230V AC,
120/240V AC
3116 SMS Panel Enclosure Includes:
ELCI Main + 3 blank circuit positions
1 ELCI Main 120V 30A, 30mA, 3102
2 small wire glands, 3124
3 medium wire glands, 3125
4 green “ON” indicating 120V AC LEDs, 8034
1 red “Reverse Polarity” indicating 120V AC LED, 8066
1 LED plug
12 circuit breaker mounting screws
6 Backlit circuit label positions
1 AC Main label, 1 Reverse Polarity label, 1 ELCI label
30 Basic AC labels, 4206
Panel Voltage ID label-120V AC
3118 SMS Panel Enclosure Includes:
ELCI Main + 2 blank circuit positions
1 ELCI Main 120V 50A, 30mA, 3103
2 small wire glands, 3124
1 medium wire gland, 3125
2 large wire glands, 3126
3 green “ON” indicating 120V AC LEDs, 8034
1 red “Reverse Polarity” indicating 120V AC LED, 8066
2 LED plugs
12 circuit breaker mounting screws
5 Backlit circuit label positions
1 AC Main label, 1 Reverse Polarity label, 1 ELCI label
30 Basic AC labels, 4206
Panel Voltage ID label-120V AC
3119 SMS Panel Enclosure Includes:
ELCI Main + 1 blank circuit position
1 ELCI Main 120/240V, 50A, 30mA, 3104
2 small wire glands, 3124
1 medium wire gland, 3125
2 large wire glands, 3126
3 green “ON” indicating 120V AC LEDs, 8034
1 red “Reverse Polarity” indicating 120V AC LED, 8066
3 LED plugs
12 circuit breaker mounting screws
4 Backlit circuit label positions
1 AC Main label, 1 Reverse Polarity label, 1 ELCI label
30 Basic AC labels, 4206
Panel Voltage ID label-120V/240V AC
3117 SMS Panel Enclosure Includes:
2 x 120V AC / 30A ELCI Main
2 ELCI Main 120V 30A, 30mA, 3102
2 small wire glands, 3124
4 medium wire glands, 3125
2 green “ON” indicating 120V AC LEDs, 8034
2 red “Reverse Polarity” indicating 120V AC LEDs, 8066
2 LED plugs
12 circuit breaker mounting screws
6 Backlit circuit label positions
Source Selection Label Set (10 labels)
2 Reverse Polarity labels, 2 ELCI labels
Panel Voltage ID label-120V AC
3120 SMS Panel Enclosure Includes:
ELCI Main for Isolation Transformer
1 ELCI Main 240V, 50A, 30mA, 3093
2 small wire glands, 3124
1 medium wire gland, 3125
2 large wire glands, 3126
2 green “ON” indicating 240V AC LEDs, 6806
4 LED plugs
12 circuit breaker mounting screws
2 backlit circuit label positions
1 AC Main label, 1 ELCI label,
Panel Voltage ID Label- 240V AC
Red circuit status indicator LED
Green circuit status indicator LED
LED plug
Backlit circuit label position