Ez-1/2/3 application information – Carlin EZ-1/2/3 User Manual

Page 4

Advertising
background image

Carlin part number MNEZ123 Rev. 07/13/11

– 4 –

Model EZ-1/2/3 oil burners — Instruction manual

1. EZ-1/2/3 application information

(continued)

Table 1

Apply the guidelines below to select a nozzle when appliance-specific nozzle data is not available from the manufacturer

(see notes at end of table for application tips). DO NOT apply for EZ-1-HP, EZ-2-HP or

EZ-3-HP models — see information supplied with appliance/burner.

EZ-1 Burner nozzle selections

Brand

Spray

Angle

&

pattern

Head positioning bars (GPH)

Flame

length

needed

0.50

.60 to .65

0.75

0.85 to 1.00

1.10 to 1.25

1.35 to 1.50

1.65

Nozzle rating, GPH

0.50

0.60

0.65

0.75

0.85

1.00

1.10

1.25

1.35

1.50

1.65

Delavan

Hollow

60ûA

•

•

•

•

Medium

Hollow

70ûA

•

•

•

•

•

•

Short

Semi-solid 60ûSS

•

•

•

•

•

Short

Solid

60ûB

•

•

•

•

•

•

Very long

Solid

70ûB

•

•

•

•

•

•

Long

Hago

Hollow

60ûH

•

•

•

•

•

•

Short

Hollow

70ûH

•

•

•

•

•

Short

Semi-solid 60ûSS

•

•

•

•

•

•

•

•

•

•

Short

Solid

60ûES

•

•

•

•

•

•

•

•

•

•

•

Medium

Solid

70ûES

•

•

•

•

•

•

Medium

Solid

60ûB

•

•

•

•

•

•

Long

Solid

70ûB

•

•

•

•

•

•

Long

Monarch

Hollow

60ûNS

•

•

•

•

•

•

Short

Hollow

70ûNS

•

•

•

Short

Semi-solid 60ûAR

•

•

•

•

•

•

•

Medium

Semi-solid 70ûAR

•

•

Short

Solid

60ûR

•

•

•

•

•

•

•

•

•

Medium

Solid

70ûR

•

•

•

•

Medium

Danfoss

Hollow

60ûAH

•

•

•

•

•

•

•

Short

Semi-solid 60ûAB

•

•

•

•

•

•

•

•

Medium

Solid

60ûAS

•

•

•

•

•

•

•

•

•

•

Medium

EZ-2 Burner nozzle selections

EZ-3 Burner nozzle selections

Brand

Spray

Angle

&

pattern

Head positioning bars (GPH)

Brand Spray

Angle

&

pattern

Head positioning bars

(GPH)

Flame

length

needed

1.50

1.65 to 1.75

2.00

2.25

2.00

2.25

2.50

Nozzle rating, GPH

Nozzle rating, GPH

1.50

1.65

1.75

2.00

2.25

2.00

2.25

2.50

Delavan

Hollow

60ûA

•

•

•

•

•

Delavan

Hollow

60ûA

•

•

•

Medium

Solid

60ûB

•

•

•

•

•

Solid

60ûB

•

•

•

Long

Semi-solid 60ûSS

•

•

•

•

•

Semi-solid 60ûSS

•

•

•

Medium

Hago

Semi-solid 60ûSS

•

•

•

•

•

Hago

Semi-solid 60ûSS

•

•

•

Medium

Solid

60ûB

•

•

•

•

Solid

60ûP

•

•

•

Long

Solid

60ûES

•

•

•

Solid

60ûB

•

Long

Solid

60ûP

•

•

Long

Monarch

Solid

60ûR

•

•

•

•

•

Monarch

Solid

60ûR

•

•

•

Medium

Semi-solid 60ûAR

•

•

•

•

•

Semi-solid 60ûAR

•

•

•

Medium

Hollow

60ûAS

•

•

•

Danfoss

•

•

•

Medium

Danfoss

Hollow

60ûAH

•

•

•

•

•

Hollow

60ûAH

•

•

•

Short

Semi-solid 60ûAB

•

•

•

•

•

Semi-solid 60ûAB

•

•

•

Medium

Solid

60ûAS

•

•

•

•

•

Solid

60ûAS

•

•

•

Long

1. In general, all the nozzles shown above will burn well. However, in short combustion chambers, solid nozzles are not recommended because the flame may impinge on the back wall.
2. If the nozzle selected for a retrofit application results in a smoky fire, you can sometimes determine the best nozzle to use by observing the flame. To do this, slowly cover the air band slots with your fingers while

the burner is firing. The flame will begin to smoke in the area where there is more fuel than air. If the smoke begins on the outer edges, try a narrower or more solid nozzle spray pattern. If the flame begins to

smoke at the tips, try a wider or more hollow nozzle spray pattern.

3. For a packaged appliance application on which the burner has been tested, use the nozzle given in the appliance manufacturer’s instructions or supplement for the best results.

Advertising