Flint & Walling NightBright Lighting System User Manual

Nightbright lighting system

Advertising
background image

NightBright Lighting System

Operating Instructions & Parts Manual

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.

Description

This lighting system is designed for use with 115/230V 1/2, 3/4 and 1 HP floating
fountain systems. Optional colored lamp kits are available in red, green and blue.
All mounting hardware is included to attach lights to fountain and connect to
control center with factory installed timer.

General Safety Information

Carefully read and follow all safety

instructions in this manual and on

control center. Keep safety labels in
good condition. Replace missing or
damaged safety labels.

This is a SAFETY ALERT SYMBOL.
When you see this symbol on

the pump or in the manual, look for
one of the following signal words and
be alert to the potential for personal
injury or property damage.

Warns of hazards
that WILL cause

serious personal injury, death or major
property damage if ignored.

!

Warns of hazards
that CAN cause

serious personal injury or death, if
ignored.

Warns of hazards
that MAY cause

minor personal injury, product or
property damage if ignored.

IMPORTANT: Indicates factors
concerned with operation, installation,
assembly or maintenance which could
result in damage to the machine or
equipment if ignored.
NOTE: Indicates special instructions
which are important but are not
related to hazards.

!

Read these
warnings and

instructions carefully. Failure to follow
could result in serious bodily injury
and/or property damage.

!

This product
contains chemicals

known to the State of California to
cause cancer and birth defects or other
reproductive harm.

!

This unit
not

tested for use in swimming
pool areas.

Electrical
installa-

tions shall be in
accordance with
National Electric
Code (NEC) and all
applicable local
codes and ordi-
nances. A licensed
electrician should
perform installa-
tion.

Be sure system is connected to a
circuit equipped with a fuse or

circuit breaker of proper size.

Protect the power cable from
coming in contact with sharp

objects, oil, grease, hot surfaces
or chemicals. DO NOT kink the
power cable. If damaged replace
immediately.

Install all electrical equipment
in protected area to prevent

mechanical damage which could produce
serious electrical shock and/or equipment
failure.

NEVER leave the control box,
fused disconnect switch,

or covers open (either partially or
completely) when not being worked
on by a competent electrician or
repairman.

Always disconnect power source
before performing any work on

or near the motor, lights or connected
load. If the power disconnect point
is out-of-sight, lock it in the open
position and/or tag it to prevent
unexpected application of power.
Failure to do so could result in fatal
electrical shock or bodily injury.


DO NOT use this system in
flammable liquids such as

gasoline, fuel oil, kerosene, etc. Failure
to follow this warning could result in
property damage and/or personal
injury.

Unpacking

Unpack and inspect system for damage.
Verify you have received the following
components:
1. Instructions
2. Warranty
3. Lights with 100 ft. power cord
4. Mounting hardware

a. Brackets (3)
b. 1/4-20 x 5/8 bolts (6)
c. 1/4-20 locknuts (3)
d. 1/4 lock washer (3)

5. Shrink tube splice kit
6. Wire tie

INSTALLATION INSTRUCTIONS

1. Required Tools and Supplies:

a. Flat screwdriver
b. 7/16" wrenches (2)
c. Crimping tool (for cable splicing

only)

d. Torch or heat gun for shrink tube

splice kit (for cable splicing only)

e. Multimeter to check voltage,

current and insulation resistance to
ground

2. Install Nightbright lighting system

to float. (See Fig 1).

a. Assemble lights (1) to mounting

brackets (2) using bolts (3), and
locknuts (5).

Hazardous voltage.

Can shock, burn

or cause death.
Ground system before
connecting to power
supply.

Specifications

120 volt
3 - LED lamps
100 ft. power cord

022901

FW1191

0909

Supersedes

0708

Advertising