Cl1000 instruction manual – Klein Tools CL1000 User Manual
Page 2
ENGLISH
7
1
6
2
3
5
600V
400V
CATIII
600V
400V
CATIII
PRESS
PRESS
V
AT
0
10
20
40
30
Apo
V
AT
0
10
20
40
30
Apo
V
AT
0
10
20
40
30
Apro
PRESS
Duty
Cycle
Hz
V
AT
0
10
20
40
30
Apo
V
AT
0
10
20
40
30
Apo
TO SELECT
Diode
Continuity
PRESS
V
AT
0
10
20
40
30
Apo
V
AT
0
10
20
40
30
Apo
V
AT
0
10
20
40
30
Apo
600V
400A
CATIII
CL1000
B
A
I
J
4
K
F
8
E
H
D
G
C
1
FEATURE DETAILS
CL1000
Instruction Manual
GENERAL SPECIFICATIONS
The Klein Tools CL1000 is an auto-ranging clamp meter. It measures
AC / DC voltage, AC / DC current, resistance, capacitance, frequency, and
duty cycle. It can also test non-contact voltage, diodes, and continuity.
•
Operating Altitude:
2000 meters
•
Humidity:
80% max
•
Operating Temperature:
0°C / 32°F to 45°C / 113°F
•
Storage Temperature:
0°C / 32°F to 60°C / 140°F
•
Accuracy Temperature:
18°C / 64°F to 28°C / 82°F
•
Temperature Coeffi cient:
0.1*(specified accuracy) / °C
•
Dimensions:
8.875" x 3.375" x 1.5" (225 mm x 86 mm x 38 mm)
•
Weight:
11 oz. (303 g)
•
Calibration:
Accurate for one year
•
Safety Rating:
CAT III 600V
•
Accuracy:
± (% of reading + # of least significant digits)
WARNINGS
To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.
• Before each use, verify meter operation by measuring
a known voltage or current.
• Never use the meter on a circuit with voltages that exceed the
category based rating of this meter.
• Do not use the meter during electrical storms, or in wet weather.
• Do not use the meter or test leads if they appear to be damaged.
• Ensure meter leads are fully seated, and keep fingers away from
the metal probe contacts when making measurements.
• Do not open the meter to replace batteries while the probes
are connected.
• Use caution when working with voltages above 60V DC,
or 25V AC RMS. Such voltages pose a shock hazard.
• To avoid false readings that can lead to electrical shock,
replace batteries if a low battery indicator appears.
• Unless measuring voltage or current, shut off and lock out
power before measuring resistance or capacitance.
• Always adhere to local and national safety codes. Use individual
protective equipment to prevent shock and arc blast injury where
hazardous live conductors are exposed.
SYMBOLS
~
AC Alternating Current
Warning or Caution
DC Direct Current
Dangerous levels
DC/AC Voltage or Current
Double Insulated Class II
Ground
Safe for disconnect
from live conductors
AC Source
A.
Use CAT III rated leads or higher. Do not attempt to measure more than
1000V DC or 750V AC or 2000µA.
B.
Keep hands below line when measuring high current levels.
C.
Auto Power-Off (Apo)
• Device will power off after 30 minutes non-use.
• Turn the dial or press a button to wake.
• Disabled during Max / Min function.
• Holding Select button while turning on disables Auto Power-Off.
D.
Select Functionality Button
• Switch between AC and DC.
• Switch between
and .
E.
Hold / Backlight / Worklight
• Press to hold the current input on the display.
• Press again to return to live reading.
• Press for 2 seconds to enable / disable lights.
• Using lights drains the battery significantly.
F.
Auto / Manual Range
• Press repeatedly to cycle through manual ranges.
• Press for 2 seconds to return to auto ranging mode.
•
AT
is displayed on LCD only during auto ranging mode.
G.
Max / Min Hold
• Press to enter Max / Min mode; the largest and smallest values
will be saved while in this mode.
• Press repeatedly to alternate between the maximum and minimum readings.
• Press for 2 seconds to return to live reading and clear the stored
maximum and minimum values.
H. I. Battery Replacement
• When
indicator is displayed on the LCD, batteries must be replaced.
• Remove the back screw and replace 2 x AAA batteries.
1.
AC Current (large): < 400A
Features:
• Center wire in guides for best accuracy.
• Opposing currents cancel. Use line-splitter (USA only) when necessary.
2.
AC / DC Current (small): < 2000µA
Features:
MAX/MIN
RANGE
HOLD
J.
Magnetic Back
• Attach instrument to metal for hands-free use.
K.
Bar Graph
• The bar graph shows an approximate analog representation
of a measurement.
• The bar graph responds much faster than the digital display.
• The scale of the bar graph is zero to the maximum reading of
the selected range.
FUNCTION INSTRUCTIONS
• Select AC or DC current source.
•
Current above 2000µA will damage instrument.
3.
AC / DC Voltage: < 750V AC or 1000V DC
Features:
MAX/MIN
RANGE
HOLD
• Select AC or DC voltage source.
4.
Frequency (Hz) / Duty Cycle (See Feature Details)
Features:
HOLD
• Select , ,or setting.
• Frequencies greater than 1MHz will display “0.000Hz”.
5. Resistance:
< 40MΩ
Features:
MAX/MIN
RANGE
HOLD
•
Do not measure resistance on a live circuit.
6. Capacitance:
< 4000µF
Features:
HOLD
•
Safely discharge capacitor before measurement.
• Reading may take up to 60 seconds for large capacitors.
7.
Diode / Continuity
Display shows:
• Forward voltage drop if forward biased.
• “O.L.” if reverse biased.
Diode Features:
HOLD MAX/MIN
• Display shows resistance.
• Buzzer sounds if less than 30
Ω.
Continuity Features:
HOLD MAX/MIN
MAX/MIN
RANGE
HOLD
Dwg Name:
CL1000-139537TART Dwg No: 139537T
ECO No:
14678 Pkg Dwg Ref: 1650 Rev: B
Color Reference:
CEN-PACK-003-A
CL1000 Instruction Manuals - MASTER.indd 5-8
11/20/2013 3:03:52 PM