Wolo 3700P SERIES Priority 2 User Manual

Wolo Lighting

Advertising
background image

INSTALLATION INSTRUCTIONS FOR ALL MODELS OF WOLO SERIES 3700

PRIORITY 2 WARNING LIGHTS PERMANENT MOUNT

Your choice of a Wolo warning light is the perfect choice to compliment your vehicle. Wolo’s warning lights are
manufactured with the finest materials. Each light is tested to
meet our high standards before it is packaged, to assure a
perfect working light. Our quality workmanship and components
are Wolo’s assurance of a product that will give years of
dependable service.
If you need help using your new Wolo warning lights, our
technicians are available to answer your questions, Monday
thru Friday, from 9 AM to 4 PM EST at 1-888-550-4676.

MOUNTING

1. Locate the position that the safety warning light is to be

mounted. Make sure the light can be seen 360 degrees.
Clean the selected location so that it is free from dirt, wax and
oil.

2. Remove the lens from the warning light’s base by unscrewing the four (4) hex screws, one on each corner of the lens.

Carefully separate lens from the base.

3. Position the warning light’s base on the selected mounting location Fig. 1. Mark the four (4) mounting hole locations and mark

the power wire hole location. Fig. 1. Remove the warning light from the mounting surface.

4. The rubber pad provided will help eliminate vibration and water leaks and has adhesive surface under the peel off paper. (DO

NOT PEEL OFF PAPER FROM PAD AT THIS TIME).
5. Clean the surface area that the light is going to be mounted to,

so it is free of dirt, wax and oil.

6. Remove the cut circles in the rubber pad. (Fig. 2)
7. Remove the paper from the rubber pad’s surface. Push the

power wires through the hole in the pad. Fig. 2. IMPORTANT:
The adhesive side of the rubber pad is placed against the base
of the light. When pad is in position on the base, press firmly on
pad for adhesive to secure the pad in place. NOTE: make sure
the pads four (4) mounting holes line up with the base of the
warning light.

8. Drill marked mounting holes and the power wire hole to

sizes shown in Figure 1 & 2.

9. Holding the light’s base push the power wire through the drilled hole on the mounting surface and position the base over the

four (4) drilled mounting

10. Secure the base of the warning light to the vehicle using

the hardware provided. To prevent vibration and water
leaks, use only the hardware provided by Wolo in this kit
and mount only as shown in Fig. 3. IMPORTANT: Tighten
screws evenly.

11. Secure the lens back in place onto the base. CAUTION:

Be sure not to over tighten which could crack the lens.

WIRING

12. Connect the warning light’s red wire labeled to (+) 12

volts, battery, alternator, etc. The 10-amps inline fuse
provided must be used to protect the vehicle.

13. Connect the other warning light’s black wire to your on/off

switch. (not provided).

14. Connect the other terminal or wire from the on/off switch to ground, any metal body bolt that is clean of paint and rust.
15. If you should need to lengthen any wires use 18 gauge or heavier. Make sure all wire connections are taped and secured.

REPLACEMENT BULB

16. WARNING: HIGH VOLT IS PRESENT IN THE LIGHT STROBE WHICH CAN CAUSE

SERIOUS INJURY OR DEATH. Before attempting to do any service, always disconnect the
light from its power source and wait a minimum of ten-(10) minutes before removing the lens
and any work is done. A serious injury can result if the bulb is touched when hot. Always wear
gloves an eye protection when removing the bulb because the bulb is pressurized and if
broken, glass can be projected.

17. Replacement with only with a Wolo 3700RB.
18. Remove the lens by removing the four screws, one screw in each corner of the lens.
19. Remove the outer lens by removing the four screws, one screw in each corner of the lens.

Remove the clear inner fresnel lens that has the bulb that needs to be replace by turning the
lens counter clockwise. The lens is secured to the base.

Advertising