Negative sign, Using backgauge position of calculations – Baumfolder BaumCut 31.5 (For serials 78N1001 thru 700N100) User Manual
Page 60
Advertising
K5A - 26
Negative result of a calculation
< minus (" - ") sign appears before number in input section >
If this result is a cutting size the negative sign needs to be deleted
Press key
< minus sign disappears >
Negative Sign
5.0 Automatic Operation
If you have set the backgauge to a cut size on a printed sheet and you want to
use this for further calculations:
Press key
< actual size appears in input section >
Switching the function off:
Press the same key again
Using Backgauge Position of Calculations
active function
Advertising
See also other documents in the category Baumfolder Equipment:
- BAUM15: Pile Folder 1st Station (from 2005 on)
- BAUM15: Pile Folder 1st Station (from 1999 thru 2005)
- BAUM20: Control Panel
- BAUM18: Pile Folder 1st Station (from 2005 on)
- BAUM18: Pile Folder 1st Station (from 1999 thru 2005)
- BAUM20: Pile Folder 1st Station (from mid 2006) - Instruction Manual
- BAUM20: Pile Folder 1st Station (from mid 2006) - Parts Manual
- BAUM20: Pile Folder 1st Station (from mid 2006) - Parts Manual
- BAUM20: Pile Folder 1st Station (from mid 2006) - Parts Manual
- BAUM20: Pile Folder 1st Station (early 2006)
- BAUM20: Pile Folder 1st Station (in 2005)
- BAUM20: Pile Folder 1st Station (from 2002 thru 2004)
- BAUM20: Pile Folder 1st Station (from 1999 thru 2001)
- BAUM20: Pile Folder 2nd Station (from mid 2006)
- BAUM20: Pile Folder 16page (from mid 2006)
- BAUM20: Continuous Folder 1st Station - Parts Manual
- BAUM20: Ifold Service Manual
- BAUM20: Ifold Operation Manual
- BAUM20: Autoset Service Manual for Pile feed
- BAUM20: Sound Cover Installation
- BAUM20: 20 Kicker Assembly Installation
- BAUM20: 1300 series Pump Replacement Manual
- 714XA
- BAUM 26: 8PG Pre-slitter kit
- BAUM 26: Pre-slitter kit (early 2004)
- BAUM 26_30: Folder 1st Station Contfeed
- BaumCut 26.4: side table
- BaumCut 26.4 (For serials 69H1122 thru 76D1132)
- Baumcut Programmable 26.4
- BaumCut 26.4 (For serials 78D1001 thru 78D1100)
- BaumCut 26.4 (For serials 78D1101 thru current)
- BaumCut 31.5 (For serials 76N1101 thru 78N1000)
- BaumCut 31.5 (For serials 700N101 thru current)
- D2 Drill
- D3 Drill (from mid 2004 thru 2006)
- D3 Drill (from late 2003 thru mid 2004)
- D3 Drill (up to mid 2003)
- D5 Drill (from mid 2006 thru end 2006)
- D5 Drill (from 2003 thru mid 2006)
- D3HD Dril
- ND5 Drill (from 2000 thru 2002)
- 714XLT: Air-Operations Manual (from 2006)
- 714XLT: Air-Operations Manual (from 2001 thru 2005)
- 714XLT: Parts Manual
- 714: Friction-Operations Manual
- 714XLT: Thrufold-Cross Carrier idler pulley assy Manual
- 714XLT: Static brush mount Manual
- 714XLT: Air-Counter retrofit Manual
- 714XLT: Batch Ctr Manual
- 714XLT: Sound Cvr Manual
- Flexifold: Pile Folder (in 2004)
- Flexifold: Pile Folder (up to 2004)
- Flexifold: 1st Station (from 2005)
- Flexifold: 1st Station (in 2004)
- Flexifold: 2st Station (from 2005)
- Flexifold: 2st Station (in 2004)
- Flexifold: 2st Station (up to)
- Flexifold: 8-Page (from 2003 thru 2005)
- Impositions and their setups
- Older Folder
- Rebuilding a small, older folder
- Rebuilding a 200 – 700 series folder
- 714XLT: Set up
- Flexifold: Turbo Wheel Upgrade Kit Installation
- BAUM20: Perforating instructions
- BAUM20: Job Setup
- BAUM20: Static Eliminator installation
- BAUM20: Split Guide installation
- BAUM18: Pneumatic Gatefold
- BAUM1620 Gapset Calibration