Banner SureCross DX80 Wireless Networks - Manual (Page 3)

2. Move DIP switch 1 to the ON position to activate Extended Addressing Mode.
3. Apply power to the Gateway.
The Gateway’s LCD shows POWER, then RUN.
4. On the Gateway, single click button 1 to advance across the menus, stopping at the DVCFG menu.
The Gateway’s LCD shows (DVCFG).
5. Single click button 2 to select DVCFG. Single click button 1 to select from the available menu options, stopping at
XADR.
6. Single click button 2 to enter the XADR menu.
AUTO is automatic binding mode and uses the Gateway’s serial number as the extended address code.
7. Single click button 1 to select manual mode.
8. Single click button 2 to enter manual mode.
MANUAL allows the user to manually enter an extended address code.
9. Single click button 2 to advance to the extended address code entry step.
After entering manual mode, use the right rotary dial to select the digits of the extended address code. The LCD shows
SET XADR 000000.
10. Use the right rotary switch to begin setting the extended address code. Digit selection begins with the left most digit.
After selecting the first digit, single click button 1 to advance right to the next digit. All six digits must be filled, even if
it is with leading zeros. For example, to use 2245 as the code, enter 002245 into the device.
To use the Gateway’s serial number, enter 000000 as the extended addressing code.
11. Continue entering the code using a single click of button 1 to advance from left to right.
After reaching the sixth digit, the curser returns to the first digit.
12. Single click button 2 when code entry is complete.
The Gateway LCD displays the entered value for confirmation by showing CONFRM XADR, then repeating back your
value.
13. Single click button 2 to save the code and exit the XADR menu.
When entering the extended address code, the digits auto fill with whatever position the rotary switch is currently in. For
example, after entering the 00 part of the extended address code 002245, the third digit auto fills with a 0 until the rotary
dial is rotated to 2.
After manually changing the extended address code on a Gateway in an existing network, change the extended address
code for all Nodes in that network by either manually setting the code on all Node(s) or by beginning the automatic
binding sequence on the Gateway and auto-binding all the Node(s).
Manually Choosing an Extended Address (Binding) Code - Node
Manually select the extended address, or binding, code when replacing components of an existing wireless network.
To determine the existing extended address code, access the DINFO (Device Information) menu of either the existing
Gateway or another Node in the network. Follow the submenu structure to the XADR display for that device.
1. Remove the Node’s top cover.
2. Move DIP switch 1 to the ON position to activate extended address mode.
3. Apply power to the Node.*
The LCD displays POWER, then RUN.
4. On the Node, single click button 1 to advance across the menus, stopping at the DVCFG menu.
5. Single click button 2 to select DVCFG. Single click button 1 to select from the available menu options, stopping at
XADR.
6. Single click button 2 to enter the XADR menu.
AUTO is automatic binding mode and uses the Gateway’s serial number as the extended address code.
7. Single click button 1, stopping at manual mode.
MANUAL allows the user to manually enter an extended address code.
8. Single click button 2 to enter manual mode.
9. Single click button 2 to enter the extended address code entry step.
The LCD shows SET XADR 000000.
10. Use the right rotary switch to begin setting the extended address code. Digit selection begins with the left most digit.
After selecting the first digit, single click button 1 to advance right to the next digit. All six digits must be filled, even if
it is with leading zeros. For example, to use 2245 as the code, enter 002245 into the device.
11. Continue entering the code using a single click of button 1 to advance from left to right.
After reaching the sixth digit, the curser returns to the first digit.
12. Single click button 2 when code entry is complete. The Node LCD displays the entered value for confirmation.
The LCD shows CONFRM XADR XXXXXX.
13. If the rotary dial hasn’t been returned to the previous Node address (device address or ID), the LCD displays the prior
setting as a reminder. Return the rotary dial to its previous Node address.
14. The new Node address setting displays (NEW NADR XX).
15. The Node confirms the new Node address by displaying CONFRM NADR XX.
16. Double click button 2 to exit the XADR menu and to return to RUN mode.
Extended Address Mode and Binding
P/N 141340 rev A www.bannerengineering.com - tel: 763-544-3164 3