Section 1:safety instructions and warnings, 01 arc welding hazards, Section 1:safety instructions and warnings -1 – Tweco FP-95 Mini MIG User Manual

Page 7: Arc welding hazards -1, Safety instructions firepower fp-95

Advertising
background image

SAFETY INSTRUCTIONS

FIREpOwER Fp-95

Safety Instructions

1-1

Manual 0-5122

1.01 Arc Welding Hazards

WARNING

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks or

severe burns. The electrode and work circuit is electri-

cally live whenever the output is on. The input power

circuit and machine internal circuits are also live when

power is on. In semi-automatic or automatic wire weld-

ing, the wire, wire reel, drive roll housing, and all metal

parts touching the welding wire are electrically live.

Incorrectly installed or improperly grounded equipment

is a hazard.

1. Do not touch live electrical parts.

2. Wear dry, hole-free insulating gloves and body protection.

3. Insulate yourself from work and ground using dry insulating mats

or covers.

4. Disconnect input power or stop engine before installing or

servicing this equipment. Lock input power disconnect switch

open, or remove line fuses so power cannot be turned on

accidentally.

5. Properly install and ground this equipment according to its Owner’s

Manual and national, state, and local codes.

6. Turn off all equipment when not in use. Disconnect power to

equipment if it will be left unattended or out of service.

7. Use fully insulated electrode holders. Never dip holder in water to

cool it or lay it down on the ground or the work surface. Do not

touch holders connected to two welding machines at the same

time or touch other people with the holder or electrode.

8. Do not use worn, damaged, undersized, or poorly spliced

cables.

9. Do not wrap cables around your body.

10. Ground the workpiece to a good electrical (earth) ground.

11. Do not touch electrode while in contact with the work (ground)

circuit.

12. Use only well-maintained equipment. Repair or replace damaged

parts at once.

13. In confined spaces or damp locations, do not use a welder with AC

output unless it is equipped with a voltage reducer. Use equipment

with DC output.

14. Wear a safety harness to prevent falling if working above floor

level.

15. Keep all panels and covers securely in place.

WARNING

ARC RAYS can burn eyes and skin; NOISE can damage

hearing. Arc rays from the welding process produce

intense heat and strong ultraviolet rays that can burn

eyes and skin. Noise from some processes can damage

hearing.

1. Wear a welding helmet fitted with a proper shade of filter (see

ANSI Z49.1 listed in Safety Standards) to protect your face and

eyes when welding or watching.

2. Wear approved safety glasses. Side shields recommended.

3. Use protective screens or barriers to protect others from flash and

glare; warn others not to watch the arc.

4. Wear protective clothing made from durable, flame-resistant

material (wool and leather) and foot protection.

5. Use approved ear plugs or ear muffs if noise level is high.

SECTION 1:

SAFETY INSTRUCTIONS AND WARNINGS

!

WARNING

PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS KEEP

AWAY UNTIL CONSULTING YOUR DOCTOR. DO NOT LOSE THESE INSTRUCTIONS. READ OPERATING/INSTRUCTION MANUAL BEFORE

INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.

Welding products and welding processes can cause serious injury or death, or damage to other equipment or property, if the operator does not

strictly observe all safety rules and take precautionary actions.

Safe practices have developed from past experience in the use of welding and cutting. These practices must be learned through study and

training before using this equipment. Some of these practices apply to equipment connected to power lines; other practices apply to engine

driven equipment. Anyone not having extensive training in welding and cutting practices should not attempt to weld.

Safe practices are outlined in the American National Standard Z49.1 entitled: SAFETY IN WELDING AND CUTTING. This publication and other

guides to what you should learn before operating this equipment are listed at the end of these safety precautions. HAVE ALL INSTALLATION,

OPERATION, MAINTENANCE, AND REPAIR WORK PERFORMED ONLY BY QUALIFIED PEOPLE.

Advertising