VICI EUT Universal Electric Actuator - Manual (Page 14)

0
Optional Serial Interface
Serial Commands
Command Modes* Description
AM<enter> 1, 2, 3 Displays the current actuator mode
AMn<enter> 1, 2, 3 Sets the actuator mode to [1] two position with stops, [2] two position without stops, or
[3] multiposition
CC<enter> 1, 2 Sends the actuator to Position B
CCnn<enter> 3 Sends the actuator counterclockwise to position nn (from 1 to NP)
CNT<enter> 1, 2, 3 Displays the current value in the actuation counter
CNTnnnnn<enter> 1, 2, 3 Sets the actuation counter from 0 to 65535.
(For example, to reset the counter, type CNT0<enter>)
CP<enter> 1, 2, 3 Displays the current position
CW<enter> 1, 2 Sends the actuator to Position A
CWnn<enter> 3 Sends the actuator clockwise to position nn (from 1 to NP)
DELn<enter> 1, 2, 3 Sets the command delimiter to [1] CR (default), [2] LF, or [3] CRLF
DT<enter> 1, 2 Displays the current delay time in milliseconds
DTnnnnn<enter> 1, 2 Sets the delay time from 0 to 65,000 milliseconds
GOnn<enter> 1, 2 Sends the actuator to position n, where n is A or B
3 Sends the actuator to position nn (from 1 to NP) via the shortest route
HM<enter> 3 Moves the valve to postion 1 (home)
ID/<enter> 1, 2, 3 Sets the ID of the actuator to / (Must be 0-9 or A-Z)
*ID*<enter> 1, 2, 3 Resets the ID to None
IFMn<enter> 1, 2, 3 Sets the interface response mode to [0] no response string when an action command
is sent, [1] basic response to action commands, or [2] extended response to action
commands (needed for BCD interface)
LGn<enter> 1, 2, 3 Sets the interface response mode to [0] no extra characters, or [1] longer response string to
be fully backwards compatible with VICI microelectric actuators
LRN<enter> 1 Forces the actuator to find the stops on a newly installed valve.
(Note: The valve must be installed before this command is sent.)
NP<enter> 1, 2, 3 Displays the number of positions the actuator is currently set to index
NPnn<enter> 2 Sets the number of ports (nn) for the current valve. (Must be an even number between
2 and 40)
3 Sets the number of positions (nn) for the current valve. (Must be an even number between
2 and 40)
SB<enter> 1, 2, 3 Displays the current baud rate
SBnnnn<enter> 1, 2, 3 Sets the baud rate to 48(00), 96(00), 192(00), 384(00), 576(00), or 1152(00). The parity setting,
number of data bits, and number of stop bits cannot be changed.
SM<enter> 3 Displays the current default rotational direction
SMl<enter> 3 Sets the default rotational direction to [F] for forward rotation, [R] for reverse rotation, or
[A] to automatically choose the shortest route.
SO<enter> 1, 2, 3 Displays the current offset value
SOnn<enter> 1, 2, 3 Sets the offset value of the first position to be any number from 1 to 96 minus the total
number of positions. Example: for a 10 position valve, the offset can be set from 1 to 86.
STAT<enter> 1, 2, 3 Displays the status of the actuator
TM <enter> 1, 2, 3 Displays the amount of time required for the previous move, in milliseconds
TO<enter> 1, 2 Toggles the actuator to the opposite position
TT<enter> 1, 2 Toggles the actuator to the opposite position, waits a preset delay time, then rotates back
to the original position.
VRn<enter> 1, 2, 3 Displays the current firmware version for [NULL], the main PCB, or [2] the serial interface PCB.
/?<enter> 1, 2, 3 Displays a list of valid commands
Modes are described on pages 4-5.
Notes:
 In this chart, nn represents numbers to be entered and l represents letters.
 <enter> = CR(0x0D)
*