Table of contents part number index, Left hand drive (s/n s1562-) – Great Plains 3S-3000F Parts Manual User Manual
Page 117
Revision
Comments
Part Description
Part No.
Ref.
Image No.
dwg15462
PIN LINCH 3/16 X 1 9/16 LONG
805-240C
1.
RPBY 808-259C
195-137H
2.
SPKT 40B23T WITH 7/8 HEX HUB
195-134H
3.
SPKT 40B34T WITH 7/8 HEX HUB
195-135H
4.
RPBY 808-258C
195-136H
5.
FLANGETTE 52 MST
822-032C
6.
BRG 7/8HEXX2.05OD SPH
822-119C
7.
WASHER LOCK SPRING 5/16 PLT
804-009C
8.
NUT HEX 5/16-18 PLT
803-008C
9.
Revised part w/4 holes order w/#28,
195-143C 1st time only (see detail in
illustration)
SEED JACK SHAFT 7/8 HEX WING
195-169D
10.
CHAIN RL #40 X 68 PITCH W/CON
809-149C
11.
PIN ROLL 1/4 X 1 1/2 LG PLT
805-180C
12.
Order only if using original shaft
RPBY 808-260C
195-138H
13.
RHSNB 5/16-18X1 GR5
802-282C
14.
SPKT 40B57T WITH 7/8 HEX HUB
195-139H
15.
Rev. 2 is not interchangeable
w/rev. 1
(S/N S1022+)
POWER SHAFT 7/8 HEX LH
195-189D
16.
1st rev.
(S/N S1021-)
POWER SHAFT 7/8 HEX LH
195-167D
16.
NUT NYLOCK JAM NUT 1/2-13
803-178C
17.
WASHER FLAT 1/2 USS PLT
804-017C
18.
NUT HEX JAM 1/2-13 PLT
803-036C
19.
NO. 40 12T IDLER SPKT.
817-025C
20.
2nd rev.
CHAIN RL #40 129 PITCHES
136-122D
21.
Use existing stock; 1st rev.
RPBY 136-122D
809-164C
21.
HHCS 1/2-13X3 1/4 GR5
802-099C
22.
Rev. 2 is not interchangeable
w/rev. 1
(S/N S1022+)
HHCS 1/4-20X3/4 GR5
802-004C
23.
1st rev.
(S/N S1021-)
HSHCS 1/4-20X3/4
801-070C
23.
WASHER LOCK SPRING 1/4 PLT
804-006C
24.
2nd rev.
SPKT 40A23X1.813-1.818 BR/6HOL
808-240C
25.
Use existing stock; 1st rev.
RPBY 808-240C
152-283D
25.
Rev. 2 is not interchangeable
w/rev. 1
(S/N S1022+); Refer to "Jaw Clutch"
for breakdown.
JAW CLUTCH CW EXT 7/8 HEX
176-042S
26.
1st rev.
(S/N S1021-); Refer to "Jaw Clutch"
for breakdown.
JAW CLUTCH CW 7/8 HEX SHORT
176-044S
26.
GREASE ZERK 1/4-28 X 45-DEG
800-058C
27.
Order only if using revised shaft (orient
as shown in detail)
SPKT 40B12 7/8 HEX BORE W/SS
808-143C
28.
(S/N S1022+)
PIN ROLL 1/4 X 3/4 PLT
805-026C
29.
01/30/14
- 117 -
195-110P
Drives
Left Hand Drive (S/N S1562-)
(Applies to 3S-3000, 3S-3000F only)