Great Plains NTA3007HD Parts Manua - Manual (Page 17)

Revision Comments Part Description Part No. Ref.
Image No. dwg29431
SQUARE LOCK PIN 166-993D 1.
SPRING COMPRESS 1 3/4 X 4 3/4 807-291C 2.
PIN ROLL 5/16 X 4 PLT 805-424C 3.
3 BOLT PIVOT CAST W/BRG SEAT 120-188D 4.
HHCS 1/2-13X2 1/4 GR5 802-038C 5.
Refer to Hydraulic Cylinder (810-631C)
for breakdown
CYL 3X14X1.25 ROD 24 1/4 RTRCT 810-631C 6.
MW COTTER PIN 2A0134 7.
MW PIN SHORT 2A0206 8.
HHCS 3/4-10X10 GR5 802-272C 9.
ARM GAUGE WHL WLDMT 166-208H 10.
PIN CLEVIS 1 X 3 11/16 GR5 PLT 805-124C 11.
TUBE, 1 1/4" DOM X .220W 8 5/8 166-811D 12.
ARM LINK ADJ WLDMT 166-216H 13.
PLATE 4 1/2 X 6 5/8 SHIM 266-024D 14.
PLATE 4 1/2 X 6 5/8 X 1/4 SHIM 266-025D 15.
HHCS 5/8-11X2 3/4 GR5 802-281C 16.
BLOCK PILLOW WLDMT 166-215H 17.
WASHER FLAT 3/4 SAE PLT 804-025C 18.
WASHER LOCK SPRING 3/4 PLT 804-023C 19.
NUT HEX 3/4-10 PLT 803-027C 20.
Shown LH 9M 10" LEFT WING WELDMENT 166-231H 21.
RH 9M 10" RIGHT WING WELDMENT 166-232H 21.
LH 7.5" LEFT WING WELDMENT 166-223H 21.
RH 7.5" RIGHT WING WELDMENT 166-226H 21.
LH WING, LEFT, 15CM SPACING 166-230H 21.
RH WING, RIGHT, 15CM WELDMENT 166-233H 21.
WASHER LOCK SPRING 1 PLT 804-027C 22.
NUT HEX 1-8 PLT 803-031C 23.
Refer to Hydraulic Cylinder (810-628C)
for breakdown
CYL 2X13X1.125 ROD (TIE) 810-628C 24.
6 1/8 EYE BOLT 194-129H 25.
WASHER LOCK SPRING 5/8 PLT 804-022C 26.
NUT HEX 5/8-11 PLT 803-021C 27.
ARM PARALLEL WLDMT 166-211H 28.
WASHER LOCK SPRING 1/2 PLT 804-015C 29.
NUT HEX 1/2-13 PLT 803-020C 30.
HHCS 1/4-20X2 GR5 802-152C 31.
PLATE, 1 1/2 LONG KEY SHAPE 266-022D 32.
NUT LOCK 1/4-20 PLT 803-007C 33.
Shown LH WING FRAME WLDMT LEFT 166-209H 34.
RH WING FRAME WLDMT RIGHT 166-212H 34.
GREASE ZERK STRAIGHT 1/4-28 800-001C 35.
HHCS 1-8X16 GR5 802-777C 36.
3 BOLT CASTING CAP 1/2" THK 266-059D 37.
10/21/13 - 17 - 166-207P
Table of Contents Part Number Index
Frame
Opener Mount to Wing
(Applies to NTA-3007HD, NTA-907HD only)