Great Plains 7336 DH Operator Manual - Manual (Page 36)

556-235M Table of Contents Index 2014-06-30
32 7000 Series II Table of Contents Index Great Plains Manufacturing, Inc.
Appendix A - Reference Information
Specifications and Capacities
Model No. 7323DH 7326DH 7329DH
Tillage Width (9" Spacing) 23' 1" (7.02m) 26' (7.92m) 29' (8.84m)
Tillage Width (7 1/2" Spacing) 22' 11" (6.98m) 25' 4" (7.75m) 27' 8" (8.43m)
Center SecƟon 9' 6" (2.90m) 9' 6" (2.90m) 9' 6" (2.90m)
Wing 6' (1.83m) 7' 6" (2.29m) 9' (2.74m)
Number of Blades (F/R) 9" Spacing 66 74 82
Number of Blades (F/R) 7 1/2" Spacing 78 86 98
Gang Angle (degrees) 20 front/18 rear 20 front/18 rear 20 front/18 rear
Gang ShaŌ 13/4" Round 13/4" Round 13/4" Round
Bearing Standards Spring C-Shank Spring C-Shank Spring C-Shank
Bearings Maintainence Free Maintainence Free Maintainence Free
Spools DucƟle cast DucƟle cast DucƟle cast
Weight (Approximately) 14,200 15,900 17,600
Weight per Ft of Cut 615 lbs 612 lbs 606 lbs
Weight per Blade (9" Spacing) 215 lbs 215 lbs 215 lbs
Transport Width 14' 14' 14'
Transport Height 11' 6" 12' 10" 14' 2"
Wing Flex (degrees) 14 up 9 down 14 up 9 down 14 up 9 down
Tire - Transport 340/60R16.5 340/60R16.5 340/60R16.5
Tire - Wing 12.5L x 15 12.5L x 15 12.5L x 15
Tire - Gauge Wheel 9.5L x 15 9.5L x 15 11L x 15
Horsepower (PTO Req/Min) 160-230 182-260 203-290
KilowaƩ 119-171 136-194 151-216
Model No. 7330DH 7333DH 7336DH
Tillage Width (9" Spacing) 30' 2" (9.20m) 33' 1" (10.08m) 35' 11" (10.95m)
Tillage Width (7 1/2" Spacing) 30' 2" (9.20m) 32' 7" (9.93m) 36' 2" (11.03m)
Center SecƟon 13' 6" (4.11m) 13' 6" (4.11m) 13' 6" (4.11m)
Wing 7' 6" (2.29m) 8' 11" (2.72m) 10' 4" (3.14m)
Number of Blades (F/R) 9" Spacing 86 94 102
Number of Blades (F/R) 7 1/2" Spacing 102 110 122
Gang Angle (degrees) 20 front/18 rear 20 front/18 rear 20 front/18 rear
Gang ShaŌ 13/4" Round 13/4" Round 13/4" Round
Bearing Standards Spring C-Shank Spring C-Shank Spring C-Shank
Bearings Maintainence Free Maintainence Free Maintainence Free
Spools DucƟle cast DucƟle cast DucƟle cast
Weight (Approximately) 18,000 19,900 21,350
Weight per Ft of Cut 597 lbs 601 lbs 594 lbs
Weight per Blade (9" Spacing) 209 lbs 212 lbs 209 lbs
Transport Width 18' 2" 18' 2" 18' 2"
Transport Height 12' 8" 14' 15' 3"
Wing Flex (degrees) 14 up 9 down 14 up 9 down 14 up 9 down
Tire - Transport 380/55R16.5 380/55R16.5 380/55R16.5
Tire - Wing 12.5L x 15 12.5L x 15 12.5L x 15
Tire - Gauge Wheel 11L x 15 11L x 15 11L x 15
Horsepower (PTO Req/Min) 210-300 231-330 252-360
KilowaƩ 156-224 172-246 187-268