Great Plains NP30A 30-foot Parts Manual - Manual (Page 27)

Revision Comments Part Description Part No. Ref.
Image No. dwg32286
NP4000 CENTER FRAME WELDMENT 407-723H 1.
Refer to Hydraulic Cylinder 810-487C
for breakdown
CYL 4X24X1.5 ROD(TIE)34.63C.L. 810-487C 2.
NP4000 GULL WING STOP 407-738H 3.
PIN CLEVIS 1 X 4.13 USBL 805-412C 4.
WASHER FLAT 1 USS PLT 804-028C 5.
PIN COTTER 1/4 X 2 1/2 PLT 805-105C 6.
BUSHING SPINDLE 1 1/2X1 1/4X1 890-011C 7.
WING PIVOT PIN WELEMENT 407-617H 8.
PIN ROLL 3/8 X 2 PLT 805-249C 9.
RH (30ft S/N B1026T- 40ft S/N
B1050-)
NP4000 INNER WING WELDMENT 407-729H 10.
Shown RH (30ft S/N B1027T+ 40ft S/N
B1051+)
NP4000 INNER WING RH 2 417-002H 10.
LH (30ft S/N B1026T- 40ft S/N
B1050-)
NP4000 INNER WING WELDMENT L 407-727H 10.
LH (30ft S/N B1027T+ 40ft S/N
B1051+)
NP4000 INNER WING LH 2 417-004H 10.
NP4000 OTR WING HNG FRONT PIN 407-732H 11.
WING LATCH 586-243H 12.
NP4000 WING LATCH INNER 407-735H 13.
HHCS 1/2-13X1 1/2 GR5 802-091C 14.
WASHER LOCK SPRING 1/2 PLT 804-015C 15.
NUT HEX 1/2-13 PLT 803-020C 16.
PIN CLEVIS 1 X 7 1/4 USABLE 805-443C 17.
NP4000 DBL HINGE BRACKET 407-731H 18.
WASHER MACH 1.5X1.00X.075 804-192C 19.
PIN COTTER 3/16 X 2 805-058C 20.
WASHER FLAT 3/4 USS PLT 804-024C 21.
NP4000 HINGE LINK 407-874D 22.
NTA WING PIVOT SLEAVE 160-404D 23.
PIN CLEVIS 1 X 2 29/64 USABLE 805-134C 24.
NP4000 OTR WING HNG REAR PIN 407-733H 25.
SNAP RING EXT 1 1/4 HEAVY 800-177C 26.
RH (30ft S/N B1026T- 40ft S/N
B1050-)
NP4000 OUTER WING WELDMENT R 407-730H 27.
Shown RH (30ft S/N B1027T+ 40ft S/N
B1051+)
NP4000 OUTER WING RH 2 417-003H 27.
LH (30ft S/N B1026T- 40ft S/N
B1050-)
NP4000 OUTER WING WELDMENT L 407-728H 27.
LH (30ft S/N B1027T+ 40ft S/N
B1051+)
NP4000 OUTER WING LH 2 417-005H 27.
NP4000 WING LATCH OUTER 407-734H 28.
HHCS 3/8-16X1 GR5 802-017C 29.
BUSHING CYL 1 1/4 X 1 X 1 890-005C 30.
Shown WING SHIM 12GA 566-240D 31.
WING SHIM 16GA 566-241D 31.
WASHER LOCK SPRING 3/8 PLT 804-013C 32.
NUT HEX 3/8-16 PLT 803-014C 33.
PIN 3/8 X 3 USABLE LW/PIN 805-001C 34.
CYL LOCK CHANNEL 20 1/4 LONG 407-905D 35.
NUT LOCK 3/4-10 PLT 803-026C 36.
HHCS 3/4-10X4 1/2 GR5 802-192C 37.
PIN, HAIR COTTER 3/16 WIRE DIA 805-088C 38.
LOCK CHANNEL HOLDER 407-766D 39.
BENT PIN 1/2 X 11 407-767D 40.
(S/N C1010J-) U-BOLT 1/2-13 X 6 1/32 X 7 1/4 806-060C 41.
10/17/13 - 27 - 407-313P
Table of Contents Part Number Index
Frame
Wing to Frame (2Pt. NP40 16 & 17 Row 5 Section Frame)
(Applies to NP 30ft. & 40ft. only)