Dell Inspiron 3700 - Manual (Page 159)

operation requires a diskette in the drive or
a hard-disk drive in the bay before it can
continue. disk drive in the media bay.
Error reading PCMCIA
card The computer cannot identify the PC Card. Reseat the card or try another PC Card that you know works.
Extended memory size
has changed The amount of memory recorded in NVRAM
does not match the memory installed in the
computer. Reboot the computer. If the error appears on the display
again, call Dell for technical assistance.
Gate A20 failure An installed memory module may be loose. Reseat the memory modules and, if necessary, replace them.
General failure The operating system is unable to carry out
the command. This message is usually followed by specific information —for
example, Printer out of paper. Respond by taking
the appropriate action.
Hard-disk drive
configuration error The computer cannot identify the drive type. Turn off the computer, remove the drive, and boot the
computer from a bootable diskette. Then turn off the
computer, reinstall the drive, and reboot the computer. Run
the IDE Devices tests in the Dell Diagnostics.
Hard-disk drive
controller failure 0 The hard-disk drive does not respond to
commands from the computer. Turn off the computer, remove the drive, and boot the
computer from a bootable diskette. Then turn off the
computer again, reinstall the drive, and reboot the computer.
If the problem persists, try another drive. Then run the IDE
Devices tests in the Dell Diagostics.
Hard-disk drive failure The hard-disk drive does not respond to
commands from the computer. Turn off the computer, remove the drive, and boot the
computer from a bootable diskette. Then turn off the
computer again, reinstall the drive, and reboot the computer.
If the problem persists, try another drive. Then run the IDE
Devices tests in the Dell Diagnostics
Hard-disk drive read
failure The hard-disk drive may be faulty. Turn off the computer, remove the drive, and boot the
computer from a bootable diskette. Then turn off the
computer again, reinstall the drive, and reboot the computer.
If the problem persists, try another drive. Then run the IDE
Devices tests in the Dell Diagnostics
Invalid configuration
information-please run
System Setup Program The system configuration information does
not match the hardware configuration. This
message is most likely to occur after a
memory module is installed. Correct the appropriate options in the System Setup
program.
Keyboard clock line
failure A cable or connector may be loose, or the
keyboard may be faulty. Run the PC-AT Compatible Keyboards test in the Dell
Diagnostics.
Keyboard controller
failure A cable or connector may be loose, or the
keyboard may be faulty. Reboot the computer, and avoid touching the keyboard or the
mouse during the boot routine. If the problem persists, run the
PC-AT Compatible Keyboards test in the Dell Diagnostics.
Keyboard data line
failure A cable or connector may be loose, or the
keyboard may be faulty. Run the PC-AT Compatible Keyboards test in the Dell
Diagnostics.
Keyboard stuck key
failure If an external keyboard or keypad is being
used, a cable or connector may be loose or
the keyboard may be faulty. If the integrated
keyboard is being used, the keyboard may
be faulty.
A key on the integrated keyboard or external
keyboard may have been pressed while the
computer was booting. Run the PC-AT Compatible Keyboards test in the Dell
Diagnostics.
Memory address line
failure at address,
read value expecting
value An installed memory module may be faulty
or improperly seated. Reseat the memory modules and, if necessary, replace them.
Memory allocation error The software you are attempting to run is
conflicting with the operating system,
another application program, or a utility. Turn off the computer, wait 30 seconds, and then restart it.
Try to run the program again. If the problem persists, contact
the software company.
Memory data line
failure at address,
read value expecting
value An installed memory module may be faulty
or improperly seated. Reseat the memory modules and, if necessary, replace them.
Memory double word
logic failure at
address, read value
expecting value An installed memory module may be faulty
or improperly seated. Reseat the memory modules and, if necessary, replace them.