Craftsman 139.53910 - Manual (Page 36)

To Addf Reprogram or Change a Keyless Entry PIN
NO TE: Your new Keyless Entry must be programmed to operate your garage door opener.
USING THE “LEARN” BUTTON
1. Press and release the "learn”
button on motor unit. The learn ■
indicator light will glow steadily for
30 seconds.
2. Within 30 seconds, enter a four
digit persona! identification
number (PIN) of your choice on
the keypad. Then press and hold
: the ENTER button. -
3. Release the button when the T
motor unit lights blink. It has
learned the code. If light bulbs are
not installed, two clicks will be....
heard. ::::::: 'V 'T
To change an existing, know n PIN ...
If the existing PIN is known, it may be changed by one
person without using a. ladder. ..: ■ ^ ^ ■ .
.
1. Press the four buttons for the present PIN, then :
press.and hold the # button.. ■ ..::::: ; ■ ;;;;; ..
The opener light will blink twice. Release, the # .
button. ■ T: T';:
2. Press the new 4-digit .PIN you have chosen, then
■■ press Enter. ■..................................... : ■ ■ ■ ■.. T.'..V: ■.. ■...... ■■. ■. ■ ■. ■ ■ ■ ■...
The motor unit lights will blink once when the PIN has
been learned- ■■ ■ ■ ^ t >■■. ' ■■■ ■' ■ ^ ^ ■ ■ ■■ ■ ■ ■ ■ ■ ■."'.■' ■■'
Test by pressing the new PIN,.then press Enter,
door should move. ..: .
■. . :: . ^
The
To set a tem porary PIN
You may authorize access by visitors or service people
with a temporary 4-digit PIN. After a programmed
number of hours or number of accesses, this temporary
PIN expires and will no longer open the door. It can be
used
to dose the door even after it has expired. To set
a temporary PIN: ::::: :::: t
1. Press the four buttons for your personal entry PIN
(not the last temporary PIN), then press and hold the
4; button. :: ; . ' ;
blink three times. Release the The opener light will
button.:::::::::::::::::::
USING THE PREMIUM CONTROL CONSOLE
NO TE: This method requires two people if the Keyless
Entry is already mounted outside the garage.
1...Enter a four digit personal .
identification number (PIN) of your
choice on the keypad. Then press
and hold ENTER. ..............
While holding the ENTER button,
press and hold the LIGHT button
on the Premium Control Console.
3. Continue holding the ENTER and
LIGHT buttons while you press
the push bar on the Premium
Control Console (all three buttons
: are held). : : ' V ........ : :
4. Release buttons when the motor
unit lights blink. It has learned the
code. If light bulbs are not
installed, two clicks will be heard.
2. Press the temporary 4-digit PIN you have chosen,
; then, press Enter,;;....... ... ..); ::: : : : '
..The openerNght will blink four times. ::)
3. To set the number of hours this temporary PIN will
.. work, press the number of hours (up to 255), then :
■...press-4i. ;■
: ., . .: .;
3. To set the number of i/mes this temporary PIN will
work, press the number of times (up to 255), then
press #.::: V ........ /
The opener light will blink once when the temporary PIN
has been learned.
Test by pressing the four buttons for the temporary PIN,
then press Enter. The door should move. If the
temporary PIN was set to a certain number of openings,
remember that the test has used up one opening.To
clear the temporary password, repeat steps 1-3, setting
the number of hours or times to 0 in step 3.
36