ProgressiveRC 1010B+ iCharger - Manual (Page 15)

-15-
iCharger Synchronous Balance Charger/Discharger 1010B+
Charging a Lithium battery in normal CHARGE mode
The iCharger first charges with constant current (CC) according to the user setting then constant voltage (CV)
when the charging voltage reaches the peak point. In the CV phase the current gradually falls. The iCharger
will terminate charging when the current falls below than 1/10 of the configured charge current.
Fast charging a Lithium battery
The iCharger first charges with constant current (CC) according to the user setting then constant voltage (CV)
when the charging voltage reaches the peak point. In the CV phase the current gradually falls. The iCharger
will terminate charging when the current falls below than 1/5 of the configured charge current. This will result
in slightly less than 100% charge but will complete sooner than the Normal charge mode.
The left side of the first line set the type of battery (LiPo, Lilo or LiFe). The
value on the left side of second line sets the charge current and the value
on the right side of second line sets the cell count and voltage of the battery
pack. After setting the current and voltage, press Start/Enter for more than
3 seconds to start the next process.
Charge current: 0.05 – 10A, Voltage: 1 – 10 series ( LiFe to 12 series)
The number of cells you set and the processor detects. If the checking
result is the same, it would enter to the next interface; if not the same, the
left side of the first line ‘R:xxSER‘ shows the number of cells detected by the
iCharger and the right side of the first line ‘S:xxSER‘ is the number of cells
set by the user. Usually, the auto-detect number won‘t exceed the number
set by the user. You should make sure that the configured number and the
actual number for the battery are the same and then you can start charging
by pressing Start/Enter. If not, press Batt type/Stop to go back to the
previous screen and adjust the setting.
Lithium CHARGE mode. The screen shows the status during the charging
process. You can stop charging at any time by pressing Batt type/Stop.
Press Inc to display each cell‘s voltage (see the balance voltage
information) and press Dec to display the General Status information.
battery
voltage
number
of cells
Series
charged
capacity
charging
time
charge
current
work
State
The fast charging mode of Lithium battery. The left side of the first line set
the type of battery (LiPo, Lilo or LiFe). The value on the left side of second
line sets the charge current and the value on the right side of second line
sets the cell count and voltage of the battery pack. After setting the current
and voltage, press Start/Enter for more than 3 seconds to start the next
process.
Charge current: 0.05 – 10A, Voltage: 1 – 10 series ( LiFe to 12 series)
The number of cells you set and the processor detects. If the checking
result is the same, it would enter to the next interface; if not the same, the
left side of the first line ‘R:xxSER‘ shows the number of cells detected by the
iCharger and the right side of the first line ‘S:xxSER‘ is the number of cells
set by the user. Usually, the auto-detect number won‘t exceed the number
set by the user. You should make sure that the configured number and the
actual number for the battery are the same and then you can start charging
by pressing Start/Enter. If not, press Batt type/Stop to go back to the
previous screen and adjust the setting.
Lithium FAST charging mode. The screen shows the status during the
charging process. You can stop charging at any time by pressing Batt
type/Stop. Press Inc to display each cell‘s voltage (see the balance
voltage information) and press Dec to display the General Status
Information.
Battery
Series
V-BP
LiPo CHARGE
1.0A 11.1V(3S)
R:02SER S:03SER
CONFIRM(ENTER)
Start/Enter
>3 seconds
Batt type
stop
Start/Enter
Batt type
stop
Charge
Current
Li03 1.0A 12.60V
CHG 00993 59m:51
battery
voltage
number
of cells
Series
charged
capacity
charging
time
charge
current
work
State
-
Dec
+
Inc
-
Dec
+
Inc
-
Dec
+
Inc
Battery
Series
V-BP Charge
Current
Li03 1.0A 12.60V
FST 00993 59m:51
LiPo FAST CHARGE
1.0A 11.1V(3S)
R:02SER S:03SER
CONFIRM(ENTER)
Start/Enter
>3 seconds
Batt type
stop
Start/Enter
Batt type
stop
-
Dec
+
Inc
-
Dec
+
Inc
-
Dec
+
Inc