CANOGA PERKINS 9171 Configuration Guide - Manual (Page 206)

CanogaOS Configuration Guide
30-13
Command Description
activate a neighboring router.
DUT1(config-router-af)# neighbor 10.10.10.10
send-community both Specify that a community attribute should be sent to
a BGP neighbor.
DUT1(config-router-af)# exit-address-family Exit the address family mode.
DUT1(config-router)# address-family ipv4 vrf vpn2 Enter the IPv4 address-family command mode.
DUT1(config-router-af)# redistribute connected Redistribute connected routes in the VRF.
30.4.5 Validation Commands
The validation commands used are show mpls ftn-forwarding and show mpls vrf-table,
ping mpls l3vpn and traceroute mpls l3vpn on PE1.
DUT1# show mpls ftn-forwarding
FEC Out-Label Nexthop Out-Intf
3.3.3.0/24 3 2.2.2.2 eth-0-12
4.4.4.0/24 1025 2.2.2.2 eth-0-12
11.11.11.11/32 1026 2.2.2.2 eth-0-12
DUT1# show mpls vrf-table
Output for VRF table with id: 1, name: vpn1
Primary FTN entry with FEC: 5.5.5.0/24, id: 1, row status: Active
Owner: BGP, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A
Cross connect ix: 1, in label: 0, out-segment ix: 1
Owner: BGP, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 1, owner: BGP, out intf: eth-0-12, out label: 1280
Nexthop addr: 11.11.11.11, cross connect ix: 1, op code: Push and Lookup
DUT1# ping mpls l3vpn vpn1 5.5.5.0/24 source 10.10.10.10
Sending 5 MPLS Echos to 5.5.5.0, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'D' - DS Mismatch,'F' No FEC Found,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
Type 'Ctrl+C' to abort
! seq_num = 1 4.4.4.2 454.07 ms
! seq_num = 2 4.4.4.2 407.52 ms
! seq_num = 3 4.4.4.2 423.09 ms
! seq_num = 4 4.4.4.2 457.07 ms
! seq_num = 5 4.4.4.2 395.24 ms
DUT1# traceroute mpls l3vpn vpn1 5.5.5.0/24 source 10.10.10.10 detail
Tracing MPLS Label Switched Path to 5.5.5.0, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'D' - DS Mismatch,'F' No FEC Found,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
Type 'Ctrl+C' to abort
0 2.2.2.1 MTU 1500 [Labels: 1026]
R 1 2.2.2.2 MTU 1500 [Labels: 1027] 194.05 ms
R 2 3.3.3.2 MTU 9182 [Labels: implicit-null] 274.25 ms
! 3 4.4.4.2 399.53 ms