Panasonic WV-CM143 - Manual (Page 12)

1. Camera Identification Setting
(CAMERA ID)
Setting Procedure
** SET UP MENU •*
CAMERA ID ill 2 3 4 ^
1 CAMERA
AUDIO SELECT SEQ
TIMING SELECT INT
SEQ TIME ADJ 1 SEC
ALARM BUZZER OH
ALARM TIME ADJ 60 SEC
AUTO RESET OH
BRIGHT COMP 12 3 4
END SET UP DISABLE
J
Press the Down Switch (T).
** SET UP MENU **
CAMERA ID
AUDIO SELECT
TIMING SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
ll CAMERA
SEQ
INT
1 SEC
ON
SO SEC
ON
12 3 4
DISABLE
1-1. Move the cursor to the CAMERA ID and select the desired camera
by using the Left (■<) or Right {►) Switch.
To set the Camera ID Display On/Off mode, press the Setup
Switch.
1-2, After completing the procedure of item 1, move the cursor to the
second line by using the Down {T) Switch,
Set the Camera Identification according to the following procedure
(1-3) and press the Setup Switch.
To register the Camera Identification, put back the cursor to the
CAMERA ID.
Note: The Camera Identification setting is not memorized unless
the CAMERA ID is selected again.
1 -3. Selectable characters are shown in the following.
(-) (+)
0 1 2 3 4 5 6 7 8 9 ; ; A B C D E F G H I J K L M N
O P Q R S T U V W X Y Z " # ' ( )
* + , - . / = — > • (blank)
Press the Setup Switch.
Character selection can be made with the Up ( A ) or Down {▼)
Switch.
Column selection can be made by the Left (-^) or Right {►)
Switch.
After completing the selection, press the Setup Switch.
To change the Camera ID of the other camera, press the Left (-^)
or Right {►) Switch.
2. Audio Selection (AUDIO SELECT)
r
*• SET UP MENU **
CAMERA ID
AUDIO SELECT
TIMING SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
L ' camera
SEQ
INT
1 SEC
ON
60 SEC
ON
12 3 4
DISABLE
After completing the selection,
press the Setup Switch.
Г
**
SET DP MEND **
CAMERA ID 12 3 4
ll CAMERA
AUDIO SELECT SEQ
TIMING SELECT INT
SEQ TIME ADJ 1 SEC
ALARH BUZZER ON
ALARH TIME ADJ 60 SEC
AUTO RESET ON
BRIGHT COMP 12 3 4
END SET UP DISABLE
Ч /
Press the Right Switch (►■).
f
**
SET DP MENU **
CAMERA ID 12 3 4
2]
AUDIO SELECT SEQ
TIMING SELECT IHT
SEQ TIME ADJ 1 SEC
ALARH BUZZER OH
ALARH TIME ADJ 60 SEC
AUTO RESET ON
BRIGHT COMP 12 3 4
END SET UP DISABLE
SET UP MENU **
CAMERA ID
AUDIO SELECT
TIMING SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
1 CAMERA
tSEQ':
^
IHT
1 SEC
ON
60 SEC
OH
12 3 4
DISABLE
2-1. Move the cursor to the “AUDIO SELECT” position.
Select the Sequential (SEQ) or Fixing (1,2,3 or 4) mode by using
the Left (◄) or Right (►) Switch.
2-2. In the Sequential mode, the audio signal is also switched accord­
ing to the channel switching.
2-3. In the Fixing mode, the audio signal is fixed to the selected chan­
nel,
3. Timing Selection (TIMING SELECT)
•• SET UP MEND **
CAMERA ID
AUDIO SELECT
TIMING SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
1 CAMERA
SEQ
[iNTj -4
1 SEC
ON
60 SEC
ON
12 3 4
DISABLE
3-1. Move the cursor to the TIMING SELECT,
3-2. Select the Interna! Timing (INT) or External Timing (EXT) by using
the Left (4) or Right (►) Switch.
Note: Set this item to the “EXT” when this timing signal is input
from the other video monitor or time lapse VTR.
-10-