Panasonic WV-CM143 - Manual (Page 13)

4. Sequential Time Adjustment
(SEQ TIME ADJ)
7. Auto Reset Setting (AUTO RESET)
** SET UP MENU ••
CAMERA ID
AUDIO SELECT
TIMING SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
1 CAMERA
SEQ
lOT
И^ЗЕСЦ]
OH
60 SEC
ON
12 3 4
DISABLE
SET UP MENU **
CAMERA ID
AUDIO SELECT
TIMING SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
L CAMERA
SEQ
INT
1 SEC
ON
60 SEC
[ON]
12 3 4
DISABLE
or
4-1. Move the cursor to the SEQ TIME ADJ.
4-2. Select the sequential time by using the Left (
Right (►) SvAfitch,
Sequential time can be selected from approx. 1, 2, 3,
4, 5, 6, 7. 8, 9, 10, 15, 20, 25 or 30 sec.
5. Alarm Sound On/Off (ALARM BUZZER)
SET UP MENU **
CAMERA ID
AUDIO SELECT
TIMING SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
L CAMERA
SEQ
INT
1 SEC
[ONj
60 SEC
ON
12 3 4
DISABLE
7-1. Move the cursor to AUTO RESET.
7-2. Auto Reset On/Off nnode can be selected by using the
Left (-^) or Right (►) Switch.
The alarm mode will be reset automatically at 60 sec,
after the sensor signal is received.
8. Bright Compensation Setting
(BRIGHT COMP)
8-1. Move the cursor to the “BRIGHT COMP”.
8-2. The desired camera can be selected by using the Left
{◄) or Right {►) Switch.
8-3. Bright Compensation On/Off mode can be selected by
using the Set Up Switch.In the sequential mode, this
function can give the suitable condition to the picture
during the sequential mode.
5-1 Move the cursor to the ALARM BUZZER.
5-2. Alarm Sound On/Off mode can be selected by using
the Left (-<) or Right (►) Switch.
This monitor sounds the alarm for the preset time when
an alarm signal is received.
6. Alarm Time Adjustment
(ALARM TIME ADJ)
□ Л
о
SET UP MENU **
CAMERA ZD
AUDIO SELECT
TIMING SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
L CAMERA
SEQ
INT
1 SEC
ON
'60.SECD
ON
12 3 4
DISABLE
SET UP MENU
CAMERA ID
AUDIO SELECT
TIMIHO SELECT
SEQ TIME ADJ
ALARM BUZZER
ALARM TIME ADJ
AUTO RESET
BRIGHT COMP
END SET UP
12 3 4
1 CAMERA
SEQ
INT
1 SEC
OH
60 SEC
OH
1 . . 4
DISABLE
□ л
о
fì.
“BRIGHCOMP" ON OFF OFF ON
6-1, Move the cursor to the ALARM TIME ADJ.
6-2. Set the time duration of the alarm buzzer by using the
Left {-^) or Right (►) Switch.
Alarm buzzer can be selected from approx, 1 , 5 , 10,
20, 30, 40, 50 or 60 sec.
Caution:
This function only works on the screen in the
sequential mode.
The video signal can not be supplied from Video
Output Connector.
When observing the playback picture, picture
adjustment should be made by using the Bright or
Contrast Control on the front panel.
-11-