Panasonic WJ-MX50 - Manual (Page 13)

108. Demo ON/OFF Switch (DEMO ON/OFF)
When this switch is in the ON position, a
preprogrammed mixer features demonstration takes
place.
109. Reset ON/OFF Switch (RESET ON/OFF)
In case the power of this unit is turned on while this
switch is in the ON position, the LED’s on the panel
light up as the factory preset. In case the power of this
unit is turned on while this switch is in the OFF position,
the LED's on the panel light up returnning to how they
were. Refer to Note 3 on page 17.
110. Sourcel COMP. Input Connector
(SOURCE1/COMP.)
This connector accepts a 1.0 Vp-p/75 ohms composite
video signal.
111. Sourcel Y/C Input Connector (SOURCE 1-Y/C)
This connector accepts the S-Video signal.
Note:
This input has a priority over that of the COMP,
Connector in the Source 1. If the S-Video signal
and the composite signal are both supplied to the
Sourcel at the same time, only the S-Video signal
is used as a Sourcel Video signal.
112. Source 2 COMP. Input Connector
(SOURCE2/COMP.)
This connector accepts a 1.0 Vp-p/75 ohms composite
video signal.
113. Source 2 Y/C Input Connector (SOURCE2-Y/C)
This connector accepts the S-Video signal.
Note:
This input has a priority over that of the COMP.
Connector in the Source 2. If the S-Video signal
and the composite signal are both supplied to the
Source 2 at the same time, only the S-Video signal
is used as a Source 2 Video signal.
114. Source Selection Switch
(EDIT CONTROL SOURCE SELECT, SOURCE)
This switch is used to choose between the Source
signals for the Editing Controller AG-A800. The relation
between this switch and the source selection switches
(P1, P2, AUX) on the AG-A800 is as follows.
WJ-MX50 SOURCE AG-A800
P1 P2 AUX
SI-2 Source 1 Source 2 Source 3
S2-3 Source 2 Source 3 Source 4
S3-4 Source 3 Source 4 Source 1
Example:
If this switch is in the Si-2 position, Sourcel is
selected when Pi button is pressed.
115. Source 3 COMP. Input Connector
(SOURCE3/COMP.)
This connector accepts a 1.0 Vp-p/75 ohms composite
video signal.
116. Source 3 Y/C Input Connector (SOURCE4-Y/C)
This connector accepts the S-Video signal.
Note:
This input has a priority to that of COMP.
Connector in the Source 3. If the S-Video signal
and the composite signal are both supplied to the
Source 3 at the same time, only the S-Video signal
is used as a Source 3 Video signal.
117. Source 4 COMP. Input Connector
(SOURCE4/COMP.)
This connector accepts a 1.0 Vp-p/75 ohms composite
video signal.
118. Source 4 Y/C Input Connector (SOURCE3-Y/C)
This connector accepts the S-Video signal.
Note:
This input has a priority to that of COMP.
Connector in the Source 4. If the S-Video signal
and the composite signal are both supplied to the
Source 4 at the same time, only the S-Video signal
is used a Source 4 Video signal
119. Advance Sync Output Connectors (ADV SYNC)
In the A/B Roll Editing System, the Advance Sync signal
from this connector should be supplied to the playback
VTR's which do not have the Time Base Corrector
(T.B.C.) inside.
Note:
The enough editing accuracy may not be obtained
without this signal. This signal is necessary for the
Compression function and Trail function when it is
recorded on the VTR,
120. Advance Reference Output Connectors
(ADV REF)
In the A/B Roll Editing System, the Advance Reference
Signal from this connector should be supplied to the
playback VTR's which have the Time Base Corrector
(T.B.C.) inside (or AUX video source).
Note:
The enough editing accuracy may not be obtained
without this signal. This signal is necessary for the
Compression function and Trail function when it is
recorded on the VTR,
121. External COMP. Input Connector
(EXT CAMERA IN/COMP.)
The external camera to be used as a Key Source is
connected to this connector when the camera has the
composite video signal.
122. External Y/C Input Connector
(EXT CAMERA IN/Y/C)
The external camera to be used as a Key Source is
connected to this connector when the camera has a
S-Video Signal.
- 12 -