CatEye MODEL EC-1600 - Manual (Page 20)

32
Select the Isopower
Training Program
Isopower (constant load) training
1
2
Input Conditions
• For program selection see the Starting Up section page 18.
TIME
PLL
TM
TLD
AGE
min:sec
watt
CONST
TIME
WARM
kg•m
TM min:sec
watt
kg•m
rpm
CONST
• After printing out the conditions, the LCD changes as in the
drawing.
• The initial workload (pedal torque) is indicated in blinking dot in
the graphic section of the LCD. One dot along the horizontal axis
indicates 30 seconds, and one along the vertical axis 0.5 kg·m. At
every 30 seconds, the row of dots will increase by one towards the
right of the graphic section, with the last row blinking.
• For the 3 minutes warming up time after starting exercise,
pedal resistance will gradually increase and WARM mark ap-
pears on the panel.
Note: During the warm up, the pedal resistance is increased so as to
reach the set wattage in 3 minutes provided you pedal at 50 rpm. If
you pedal faster than 50 rpm and reach the set wattage earlier than
3 minutes, the warm up is finished at that moment.
Remark: If you first press the MODE button, and holding it down
press the ADV button to start the program, instead of just press-
ing the ADV button, you can skip the warm up phase and start
the exercise at the preset wattage from the scratch.
4
Start / Warm Up
3
Start Program
• After setting your conditions, adapt the earlobe pulse sensor
and depress ADV button to start program.
• Input age, pulse limit, exercise time and set wattage. The initial
display prior to input is as in the drawing. The numeric for age is
blinking.
Initial Value Setting Range
Age 40 10~ 99
Pulse Limit 160 bpm 80~ 200 bpm
Exercise Time 20 min 0~ 99 min
Set Wattage 60 watts 25~ 200 watts
• The pitch sound to adjust your cadence at 60 rpm (rings every
half second) is set "OFF".
• There is no graphic display yet in the LCD.
• You can increase or decrease the blinking numeric by pressing
the buttons.
• Press the MODE button to change the blinking numeric.
33
• After the WARM symbol goes out, the pedal resistance (torque
kg·m) increases or decreases according to the pedal cadence.
During exercise the pedal resistance (torque: kg·m) changes in
0.1 kg·m units to maintain the set value for wattage.
• Target wattage can be changed during exercise by pressing
either or button. The new target wattage will be dis-
played for 2 seconds in place of the current wattage.
Note: For calculation purposes, pedal cadence under 40 rpm is
regarded as 40 rpm, and pedal cadence over 100 rpm is re-
garded as 100 rpm.
Remarks: The graphic section will display the torque pattern for
maximum 16 minutes. At the end of the 16 minutes period, the
torque pattern once disappear and the actual torque at that mo-
ment will be displayed flashing at the left end of the section.
TIME
kg•m
TM min:sec
watt
kg•m
rpm
CONST
TIME
COOL
kg•m
TM min:sec
watt
kg•m
rpm
CONST
• If the 5 minute cool down phase has elapsed or if you press the
ADV button, the buzzer sounds and the program ends. The
calorie consumption is printed out, and the LCD returns to the
initial screen.
• If you are completely finishing the exercise, be sure to switch off
the unit.
Sample print out
6
5 Exercise at Constant
Wattage
Finish Exercise
Cool Down
7
End Program
• The buzzer sounds at the specified time.
• If you press the ADV button, the program enters a 5 minute
cool down phase and the COOL symbol lights up. Then the
pedal resistance becomes the minimum of 0.5 kg·m.
Note: Even if the buzzer sounds, the program does not enter
the cool down phase unless you press the ADV button.
• The LCD still displays the same exercise data.
• Shows that the Isopower (constant load)
training program has been performed.
• Set wattage
• Upper limit pulse rate
• Calorie consumption