Panasonic GP-US532H - Manual (Page 6)

7. Camera/Color Ваг Selector (CAM/BAR)
This selector is used to select either the video sig­
nal or the SMPTE color bar signal which is output
from the video output connector (VIDEO), YC (S-
VIDEO) output connector or RGB (D-SUB, 9-pin)
output connector,
CAM :The video signal from the camera is output.
BAR : The SMPTE color bar signal is output.
Set this switch to BAR when making video monitor
adjustments and recording the color bar signal.
8. White Balance Selector (ATW/AWC/MANU)
This selector is used to select the white balance
mode from followings.
ATW ; In this mode, the color temperature is moni­
tored continuously and thereby white balance
is set automatically.
AWC : In this mode, accurate white balance is
obtained.
The white balance settings are as follows:
1. Aim the camera at white chart.
2. Press the ITEM (AWC) button on the front
panel to set the white balance.
3. When the auto white balance is completed,
the auto warning indicator goes off after
blinking.
If the auto warning indicator is kept being lit,
follow the setting procedures above for auto
white balance setting again.
MANU : The white balance can be adjusted manu­
ally by the red gain (R GAIN) and blue gain
controls (B GAIN).
9. Auto Warning Indicator
This indicator blinks while the white balance or
black balance is being automatically set. This indi­
cator lights continuously when the white balance or
black balance is set improperly. In this case, follow
the auto white balance or black balance setting
procedure.
10. Red and Blue Gain Controls (R GAIN/B GAIN)
These controls are used to manually adjust the
white balance.
These controls only work when the white balance
selection switch (ATW/AWC/MANU) is set to
MANU.
Turn the controls clockwise to increase the red and
blue signal levels, and counterclockwise to
decrease.
12. Item Button (ITEM/AWC)
While the SET UP menu is displayed, this button is
used to move the cursor to the downward.
Normally, when the white balance selection switch
(ATW/AWC/MANU) is set to AWC, this button is
used to set the automatic white balance control
(AWC).
13. Left Button (-^/ABC)
While the SET UP menu is displayed, this button is
used to move the cursor to the left.
Normally, this button is used to set the automatic
black' balance control (ABC).
14. Right Button (►)
This button is used to move the cursor to the right
in the SET UP menu.
15. Scene Fite Selector (SCENE)
This selector is used to select the scene files.
16. Electronic Light Control ON/OFF Selector
(ELC ON/OFF)
This selector is used to select the electronic light
control from followings.
ON : In this position, the electronic light control
(ELC) mode is selected and the Electronic
Shutter Speed (SHUTTER) mode is interrupted.
OFF : In this position the shutter speed mode
(SHUTTER) is selected and electronic light
control (ELC) mode is interrupted.
Note :
• Confirm the setting of the ELC and SHUTTER
parameters on the SET UP menu.
17. Electronic Shutter Speed Control (LEVEL)
This control is used to set the target value of
Electronic Shutter Speed between 1/60 and
1/10 000 second together with ELC ON/OFF switch.
18. Title Input Connector (TITLE)
This connector is used to connect the optional
Character Generators WJ-KB30 or WJ-KB50.
Note:
The Black & White characters of the generator
are mixed with the video signal and are
obtained at VIDEO OUT, S-VIDEO (Y/C) OUT
and RGB/SYNC OUT connectors.
No colorization of the character is available.
11. Page Button (PAGE)
This button is used to display the SETUP MENU by
pressing for 2 seconds or more, and to change the
parameters in the SET UP MENU.
-
4
-