Hardy Floor Scales - Manual (Page 8)

Table of Illustrations
I
Table of Illustrations
HARDY - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1
FLOOR SCALES - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1
OPERATION AND INSTALLATION- - - - - - - - - - - - - - - - - - 1
MANUAL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1
TABLE OF CONTENTS - - - - - - - - - - - - - - - - - - - - - - - - I
TABLE OF ILLUSTRATIONS - - - - - - - - - - - - - - - - - - - - - I
INSTALLING THE CLOSED EYE BOLTS INTO THE TOP PLATE - - - 4
SUMMING JUNCTION CARD- - - - - - - - - - - - - - - - - - - - - - 5
DRIVING HEAVY EQUIPMENT ON AND OFF THE SCALE - - - - - - 7
MAXIMUM HEIGHT - - - - - - - - - - - - - - - - - - - - - - - - - - 8
SPIRIT LEVEL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
CHECKING PLATFORM LEVEL/SIDE TO SIDE - - - - - - - - - - - - 9
CHECKING PLATFORM LEVEL/CORNER TO CORNER - - - - - - - - 9
CHECKING PLATFORM LEVEL/DIAGONALLY - - - - - - - - - - - - 10
ADJUSTING THE FEET FOR LEVEL - - - - - - - - - - - - - - - - - - 10
SCALE VERIFICATION/POSITION #3 - - - - - - - - - - - - - - - - - 13
REMOVING THE SUMMING BOX COVER - - - - - - - - - - - - - - - 16
REMOVING THE SUMMING BOX LID - - - - - - - - - - - - - - - - - 17
REMOVING THE SUMMING BOX LID - - - - - - - - - - - - - - - - - 18
INSERTING THE LEVELING FOOT INTO THE LOAD SENSOR - - - - 19
INSIDE VIEW - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
OUTSIDE VIEW - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
ALL FOUR FEET INSTALLED - - - - - - - - - - - - - - - - - - - - - 21
SUMMING CARD - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21
CABLE GLAND - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23
REMOVING LOAD SENSOR BOLTS AND FEET - - - - - - - - - - - - 24
FOUNDATION FOR THE PIT FRAME- - - - - - - - - - - - - - - - - - 26
PIT FRAME DIMENSIONS - - - - - - - - - - - - - - - - - - - - - - - 27
DRAIN INSTALLATION DIMENSIONS - - - - - - - - - - - - - - - - - 28
EXCAVATED PIT AND SUPPORT FOR THE PIT FRAME - - - - - - - 29
RAMP WITH RETAINER PLATES - - - - - - - - - - - - - - - - - - - 31
INSTALLING ANCHORS FOR RAMP - - - - - - - - - - - - - - - - - - 31
FOOT RETAINER PLATES INSTALLATION - - - - - - - - - - - - - - 33
BUMPER GUARD/GAP REQUIREMENT - - - - - - - - - - - - - - - - 35
BUMPER GUARD/INSTALLATION- - - - - - - - - - - - - - - - - - - 35