Kenmore POWER MISER 153.330652 - Manual (Page 18)

OPERATING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING Í
B.
r
WARNING: If you do lot follow tiese instruclons exactly, a fire or exptosioB
may rtsul caBsIng propirty damag#, ptrsoial iij«ry or loss of life.
This appllanci has a pitot which is lightei by a
pltwttedric igiiter. Whei llghing the plot, foiowthese
instrycttoos aacttf,
BiFOti LIGHTING smell all iround the ippliance^ area
for gas. Be su« to siiill next to the fbor l»cayse some
gas is lei¥iif than air »d wll selle on the floor.
WHAI10 00 IF YOU SiELL GAS:
• Do not try to ight any appliance.
Do not touch any ilictricil sytch; do not use liy
phone In your hjiWng.
• IfPiwd' ^ fpiwdialely call your gas supplier from a
neighbor’s phorie. follow ®i gas supplier’s
Instructions.
If yoi cannot reach your ps suppler, call the ire
department.
C. Use Oily yoBr hand to push In or turn tii ps control
knoll. Never use tools. If the knob wll not push in or
move by hand, don’t fry to repir it, call a quatied service
taehiildai. Force or atteraptid repair may result In a fi»
or explosion.
D. Do not use ihis appliance if any part has ta«fi under
water. ImiBdiately call a qwifled service technician to
inspect titi appliance. Water heaters subjected to flood
conditions or anytime the gas controls, main bunier or
pilot have been submerpd to water require replacement
of the enir« water heater.
E. 00 HOT USE THIS APPLIAiCE IF THERE HAS KEN AM
ENmOM OF VAPORS. Imiwdiatefy call a q«all«i service
liclnlciai to inspicl th# appliance. Water heaters
subjected to a flaiwabte vapors ¡gBitloi ««II show a
iiscoloratlon on the air Intake grid and require
replaciment of the enire water htator.
LIGHTING INSTRUCTIONS!
STOP! I is imperative that you read all thesaWy wmlnp
before fighting the pilot.
Remove the orter door.
Tim tie temperiture dial co«nterclocMs# ^ to its
lowst setting.
I, Depress the refit tatton til the way
In and liiEDIATELY depress the
ifilter botton inti fm hear a loud
click. Observe the pilot through th«
view port. iO' not release the reset
bulot. Repeat tamtdlatily I pilot
does not ifht on the irst fry. I the
pilot does iot light by the fourth
attempt lith the igniter, repeat steps
4 - 7. Continue to hold the biitton for
about |1) ninite after the pitot is II.
iileasi the reset bufcn and It *11 pp
back up. Pilot »hould rtmain III If tie
pilot light goes art, rtpeat step 3 • 7.
PUSHBUTTON
IGNITER
Depress the dial stop aid torn
gas control InobclocWs»
tottii“OFF"posiioi.
5. To dear any ps that miy haw
attumtilited wit tm f10| mtoites.
If you tie« smell gas, STOP! Follow “1" ¡n the safety
wamlig atove. If you do «ot smell gas go to the next
step.
6. Tim tin gas control knob^
eountercloclvis#
to “PILOT".
liPORTAiT: ff th« pilot will not stay lit after several tries,
depress the dial stop and iinii ps cwitrd Inob to “OFF”,
then call ycwr rerwce technician or gas supplier,
liPORTANT: If the reset bitten |see irapllc at step 3} does
not pp Bp when released, stop and ¡mmediately slit off
the gas at the line valve or tank. Call your service technician
or ps supplier.
S. Turn the gas confrol knob
couaterclockwisi O
to “ON”.
i, Set the temperature dial to
tte desired sifting.
10, Replace the otiter door.
1 Tim tIi te«per#ture dial countircloctolseO to Its
loiwsl setting.
TO TURN OFF GAS TO APPLIANCE
2
.
Turn the gas confrol knob clockiási ^ to tti* “OFF*
poslion.
18