RCA LCD L26HD35D - Manual (Page 17)

TV operation
1
3
4
To turn on the TV, press POWER.
(POWER indicator on the front of the unit
changes green, it may take approx. 10 seconds
for a picture to appear on screen.)
Adjust the voiume ievel by pressing VOL + or -.
The volume levei wili be indicated on the screen
by blue bars. As the volume level increases, so do
the number of bars. If the volume decreases, the
number of blue bars also decreases.
Set the Signal Type option to the appropriate
position (see “Air/Cable selection” on page 15).
Press the Direct Channel Selection (0-9, -)
buttons to select the channel.
(If you press only channel number, channel
selection will be delayed for a few seconds.)
TO SELECT ANALOG CHANNELS
1 -9: Press 1 -9 as needed. Example, to
select channel 2, press 2
,
then press
ENTER.
10-99: Press the 2 digits in order. Example,
to select channel 12, press 1,2, then
press ENTER.
100-135: Press the 3 digits in order. Example, to
select channel 120, press 1,2,0, then
press ENTER.
TO SELECT DIGITAL CHANNELS
Press the first 3 digits, then press the - button,
followed by the remaining number.
Example, to select channel 015-001, press 0,1,
5, -, 0, 0, 1, then press ENTER.
• If a channel is selected with only audio content,
“Audio only” will be displayed on the screen.
• If a channel is selected with a weak digital
signal, “Digital channel signal strength is low”
will be displayed on the screen.
The same program may be available on either
an analog channel or a digital channel. You may
choose to watch either format.
• If a channel is selected to which you have not
subscribed, “Digital channel is encrypted” will
be displayed on the screen.
VHF/UHF/CABLE CHANNELS
Air Cable
VHF VHF
2-13 2-13
UHF STD/HRC/IRC
14-69 14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-135 (100) (135)
01 (4A)
NOTE:
• If a channel with no broadcast is selected, the
sound will automatically be muted.
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.
To select the video input source
To view a signal from another device connected to
your LCD TV, such as a VCR player, press INPUT
SELECT, then press
a / t or corresponding Number
buttons (0-7), then press ENTER. You can select TV,
Video 1, Video 2, Component, HDMI1, HDMI2, PC
or DVD depending on which input jacks you used to
connect your devices.
•
CHA/V
Press and release CH A/v. The channel automatically
stops at the next channel set Into memory.
For proper operation, before selecting channels, they
should be set into the memory. See “Memorizing
channels” on pages 15 and 16.
DISPLAY
Press DISPLAY to display the current information on
the screen.
When the TV receives a digital signal, the digital
information will appear.
Channel number >
Channel label (if preset) >
V-Chip rating
>
Sleep timer >
Program guide >
Resolution
Station name
Broadcast program name
Signal type
Audio language
Picture size
When the TV receives a analog signal, the analog
information will appear.
• Channel number
• V-ChIp rating
• Sleep timer
• Audio information
(Stereo, SAP or Mono)
• Channel label (if preset)
• Signal type
• Picture size
• Resolution
Press DISPLAY again to clear the call display.
NOTE:
• After a few seconds, DISPLAY screen will return to
normal TV-operation automatically.
RECALL
This button allows you to go back to the last channel
selected by pressing RECALL. Press RECALL again
to return to the last channel you were watching.
17