Garelick 75090 LOW PROFILE SEAT SLIDE AND LOCKING SWIVEL - Manual

Assembly and Installation Instructions for
Swivel/Seat Slide Systems
Form 12.232
ASSEMBLY INFORMATION
1. Read instructions completely before starting assembly.
2. For product integrity during shipment, your slide has been se-
cured with a transit screw. Remove screw prior to assembly.
ASSEMBLY INSTRUCTIONS
Refer to Fig. 1
1. Slide the track plate (A) out of the swivel base as shown.
Refer to Fig. 2
1. Position the track plate (A) on your seat’s bottom.
2. Align the holes in both the seat and track plate. Secure the track
plate to your seat with appropriate hardware. NOTE: Fastener
suggestion is illustrated, fasteners are not provided. NOTE: All
EEz-In seats use 1/4"-20 threaded T-nuts.
Special NOTE: For Rotational Molded EEz-In Seats.
When attaching a slide to an EEz-In Rotational Molded Seat:
1. Remove the reinforcement brackets from the seat bottom
prior to installation.
2. Make certain that the portion of the screw entering the seat
shell’s T-nut does not exceed 3/8". Seat shell T-nuts are 1/4"-
20 thread. Use only 1/4"-20 machine screws.
Refer to Fig. 1
1. Slide track plate (A) with seat onto the swivel base. Position the
system where it is to be mounted. Check to see that the seat will
slide and rotate where it is located. NOTE: This swivel system is
designed to rotate with a person seated in it. For this reason, it
will not turn easily by hand. It is recommended that one side of
the swivel is clamped or held in place in order to rotate the swivel
when it is not mounted.
2. Mark and drill the four swivel base mounting hole locations on
the deck where the system is to be mounted.
3. Make sure the deck is sufficiently rigid to support this load. If it
is not, this area should be adequately reinforced. Use a backing
plate if necessary to make a secure attachment. It is
recommended that the fasteners used go through both deck and
backing plate. Washers and locking nuts should be used to
secure this system in place. Four holes are drilled in the base for
attachment but fasteners are NOT provided for this application
as the type needed may vary.
Refer to Fig. 3
1. Slide the seat and track plate off of the swivel base.
2. Lift the locking handle (B) on the swivel base and move it to the
right or left. This will disengage the locking pin.
3. Rotate the swivel plates as shown to reveal the mounting holes.
NOTE: It is recommended to clamp one side of the swivel in
order to facilitate turning.
4. Secure the swivel base in place using appropriate hardware.
NOTE: These mounting holes are 19/64" in diameter. It is rec-
ommended to through bolt this system in place.
Refer to Fig. 1
1. Slide the seat and track plate (A) back onto the swivel base as
shown.
2. Align the holes in the locking nut (C) and slide plate. NOTE:
Align the holes in the locking nut and poly sleeve if necessary.
3. Slip the stainless steel washer (D) onto the locking knob (F) as
shown. Insert the locking knob into the slide plate’s hole and
thread it into the locking nut (C). Secure the slide in position.
TO OPERATE
Sliding: Loosen the locking knob and slide the seat to the desired
position. Tighten the handle to secure the slide in place.
Swiveling:
Lift the locking handle and rotate the seat. Let go of the
handle and the seat will lock in the next available locking hole. Lock-
ing holes are set at 45° increments. If it is desired to have free
swiveling, simply lift the locking handle and move it to the left or right.
This will keep the pin from engaging the locking holes.
NOTE: Locking knob “F” must be secured tightly before motoring.
FIG. 2
Write for
a Complete
Catalog
Phone: 651-459-9795
PO Box 8, 644 2nd Street E-mail: [email protected]
St. Paul Park, Minnesota 55071 On the Web: www.garelick.com
7/04
FIG. 1
FIG. 3