New England Arbors VA84027 - Manual

13
Part # Description Quantity
"TTFNCMZ

.PVOUJOH
*OTUSVDUJPOT
/FXQPSU
"SCPS
- Read instructions through carefully before
beginning assembly.
- Identify each component from material list.
- When assembling components, place on a
non-abrasive surface to avoid scratches.
- Do not use excessive force when assembling
components.
- In the event of missing or defective parts,
please call our customer service department
at 1-800-282-9346 (ext.#20).
(FOFSBM
*OGPSNBUJPO
- Cordless drill & #2 Robertson bit
- Tape measure
- Level
- Shovel
5PPMT
3FRVJSFE
1 4” sq. x 84”
(Std)
or 120”
(Pro)
Posts
2 84” Long molded arches
3 4” sq. Locking arch/post inserts
4 4” sq. Trim caps
5 1 3/4” sq. Pergola end caps
6 1 3/4” sq. x 31 5/8” Top/bot rails
7 1 3/4” sq. x 31 5/8” Middle rails
8 1 3/4” sq. x 39” Filters
9 7/8” x 1 1/2” x 58” Spindles
10 Keystones (base & locking top)
11 Hardware kit (Includes):
1 1/2 oz. tube of glue
3/4” Stainless screws
3” Stainless screws
Cap/washer assembly
(tan model only)
4
2
4
4
20
4
2
10
10
2
2
32
20
52
- 4” sq. treated wood posts.
- Pre-mix concrete
(recommended for added strength
and stability, especially when attaching a gate).
.BUFSJBMT
*ODMVEFE
87 1/2”
50”
.BUFSJBMT
0QUJPOBM

Part 1
Part 2 Part 3
Part 4
Part 6
'JH

Product dimensions & part
identification.
'JH

Post layout for installation.
24”
Opening
58”
93 3/4”
50”
If you have any questions concerning the assembly or installation of this product and require assistance, please call our Customer service
department at 1-800-282-9346 (ext.#20), Weekdays from 8:00 am. to 4:00 pm. Eastern standard time.
If you have any comments or suggestions about our product or service, please let us know! Call: 1-800-282-9346 (ext.#24). or E-mail:
[email protected]
To learn more about us, visit us on the web at: www.newenglandarbors.com
2VFTUJPOT


Part 5 Part 8
Part 9
Part 7
32”
Ver 1.07
Part 10
14
Determine the location for your arbor, and measure out the exact
distance between the posts as shown in (Fig. 2) on the front
cover. Once you’ve verified the measurements, mark each post
location on the ground. Note: If you’ve purchased the Aussie
Auger mounts, please refer to the their instructions to complete
the installation.
15 Dig four holes in the marked locations. For the “pro model”
holes will need to be 36” deep. For the standard model we
recommend a minimum depth of 24” to provide a secure footing.
If you’ve not purchased Aussie Auger mounts, use 4x4 treated
posts to mount your arbor. Slide them inside the vinyl posts and
fasten with screws (not included) through the bottom just below
the base moldings.
Slide each trim cap up to the underside of the arch, and press the
cap firmly against the flat of the arch. Hold for a few seconds to
allow the glue to bond. Using four 3/4” screws per post, fasten
through the post & into the arch insert just below each trim cap.
Note: If your arbor is tan, use the included cap/washer
assemblies along with the screws.
16
With assistance, place your arbor into the holes and check each
post for level. Verify the measurements between the posts, and
make adjustments as needed. When the desired orientation has
been achieved, fill in the holes. We “strongly” recommend using
concrete for this, especially if you have plans to attach a gate to
your arbor.
17
Brace the arbor to keep it steady while the cement cures. Make
sure to slide the base moldings down to ground level when
finished. There should be a least a 2” gap between the top of the
base molding and the bottom rail.
If you have not purchased the optional
trim kit, please disregard this step.
84” 45”
'JH

Cap/washer assembly.