OFM T4896MB - Manual

Assembly Notes:
During assembly, hand tighten screws only. When all screws
are in place, you may then tighten all screws completely.
CAUTION:
1. Do not use this table as a step ladder.
2. Check for loose screws and tighten them every 6 months.
Model T4896MB
Mesh Base Conference Table 48” x 96”
Parts Listing
919-362-4765 (fax)
www.ofminc.com
161 Tradition Trail, Holly Springs, NC, 27540
800-520-7471 (voice)
919-303-6389 (voice)
[email protected]
08.22.2012
STOP
Assembly Instructions
Tools Needed: Allen Wrench (Included), Adjustable Wrench (Not Included)
Please read all instructions before assembly.
Step 1a:
Set Leg Posts (E) on floor with rim facing up. Insert Right/Left Base (B) and Middle Base (C) into the bottom of the Leg Posts (E)
as shown. Cover bottom with Washers (G), and insert and hand tighten Long Bolts (M) through Washers (G) and into Posts (E).
Screw Leveling Glides (H) into bottom of Bases (B). Attach Cross Support Bars (F) to top of Leg Posts (E) by inserting 8x20mm
Bolt (L) through Cross Support Bars (F) and into Leg Posts (E). Only hand tighten bolts. Repeat steps for second leg.
Step 2: Insert Brackets (I) into the open ends of Center Support Beams (D). Using a second person to help, attach Center Support Beams
(D) to Cross Support Bars (F) by sliding Beams (D) onto plates on the inside of Cross Support Bars (F). Make sure Bracket (I)
is below plate. Insert 8x20mm Bolts (L) into first two holes on Center Support Beams (D) and hand tighten using (O) Wrench.
Step 3a: Attach Peak Connectors (J) to Center Support Beams (D) by aligning in the corners as shown. Insert 8x20mm Bolts (L) through
Peak Connectors (J) into Center Support Beams (D) and hand tighten. Step 2 Bolts should fit in top space on Peak Connector (J).
Step 3b: Attach Peak Connectors (J) to Leg Posts (E) by inserting 8x20mm Bolts
(L) through Peak Connectors (J) and into Leg Posts (E). Securely tighten
all screws inserted so far using (O) Wrench.
Step 4: Place Table Top (A) upside down on a clean surface.
Insert Table Top Bolts (N) through Cross Support Bars (F)
and Center Support Beams (D) and into the aligned holes in the
Table Top (A). Securely tighten all Table Top Bolts (N) using Allen
Wrench (P) only when all 20 have been inserted.
Step 5: Securely attach two halves of Table Top (A) together by inserting
Pull Bolts (K) into adjoining holes on the underside of Table
Top (A) as shown. When inserted, tighten the Pull Bolts (K) using
a wrench (not supplied) to pull and secure the two halves together.
1
F
L
E
B
H
C
G
M
2
F
D
L
I
3
3A
3B D
L
E
L
J
4
N
A
D
N
F
5
G
K
D
A
A
Table Top
1 Unit
B
Right/Left Base
2 Sets
C
Middle Base
2 Units
E
Leg Post
4 Units
F
Cross Support Bar
2 Units
D
Center Support Beam
2 Units
J
Peak Connector
4 Units
I
Bracket
4 Units
K
Pull Bolt
4 Units
G
Washer
4 Units
H
Leveling Glides
4 Units
M
Long Bolt
8 Units
L
8x20mm Bolt
20 Units
N
Table Top Bolt
20 Units
O
Large Allen Wrench
P
Small Allen Wrench