Installation instructions (cont'd), Form i-xe/crgb/rpb, page 40 – Reznor XE Unit Installation Manual User Manual
Page 41
Form I-XE/CRGB/RPB, Page 40
7
8
9
10
12
13
14
15
16
17
18
19
20
21
L1
L2
8
BL
BK
W
7
BR
L1
L2
62
63
63
62
BL
BR
BR
4
5
RELAY CONTACTS
DISCHARGE DAMPER
2
DISCHARGE DAMPER MOTOR
WITH AUXILIARY SWITCH
L1
L1
L2
L2
BL
R
O
BR
CW
COM
CCW
FUSE
8.0 AMP
BK
BK
BK
W
W
11
R
6
40 VA. DISCHARGE DAMPER MOTOR
TRANSFORMER
26
25
24
22
23
27
BL
T3
L3
208/3/60
GRD
L1
G
BK
CONTACTS
BLOWER RELAY
BK
1
3
S
BK
BK
L2
T2
CONTACTS
BLOWER MOTOR
CONTACTOR
L1
OVERLOAD
RELAY
T1
96
O.L.
95
W
CR
12
A2
A1
W
BLOWER MOTOR
CONTACTOR COIL & O.L.
7 - 8 - 9
L2
MOTOR
BLOWER
24V
BR
208V
R
Y
BL
BK
*
*
*
*
WIRES SHIPPED IN DOWNTURN
PLENUM FOR FIELD WIRING
BK
CONTACTS
FAN CONTROL
8
BL
8
BL
8
8
BL
BL
BL
8
1
28
SWITCH
CONTROL
ON-OFF
DP-ST
8
Y
DISCHARGE DAMPER
AUXILIARY SWITCH
SET TO CLOSE WHEN
DAMPER IS A 20% OPEN
CONTACTS
FAN CONTROL
BL
1
R
Y
52
3
Y
52
3
R
Y
52
COM
NO
Y
NC
10
R
10
10
10
R
R
R
10
R
10
10
R
R
HEAT PERMISSIVE
RELAY CONTACTS
BK
35
2
4
BK 34
BR
22
Y
POST PURGE
RELAY CONTACTS
BL
R
2
5
53
4
PR
Y
R
R
R
3
CR
27
BR
1
7
3
25
CR
3
3
CR
CR
24
23
CR
1
1
1
7
BK
3
21
CR
1
BR
BR
EXHAUST
15 - 16
RELAY COIL
12
RELAY COIL
BLOWER
27 - 28
RELAY COIL
21
HEAT PERMISSIVE
RELAY COIL
BR
BR
BR
7
7
7
7
7
HEATER
RELAY COIL
39
POST PURGE
BR
7
H1
24V
208V
X1
H2
X2
H3
200 VA CONTROL
TRANSFORMER
BR
BK
W
*
*
(SEE NOTES)
DISCONNECT SWITCH
OPTIONAL FIELD WIRING
OPTIONAL FACTORY WIRING
FACTORY WIRING
FIELD WIRING
REMOTE CONSOLE
BLOWER COMPARTMENT
UNIT #2
UNIT #1
WHITE - W
PURPLE - PR
BLUE - BL
GREEN - G
YELLOW - Y
ORANGE - O
RED - R
BROWN - BR
BLACK - BK
WIRING CODE
FIGURE 46G - Sample of a Partial Wiring Diagram showing Typical Field-wiring Connections for Optional Discharge Damper
36. Optional Cooling Coil Cabinet, Option AU (Outdoor Models) (cont'd)
Installation Instructions (cont'd)
FIGURE
46F
On the
furnace
section,
remove
the center
hole plug
FIGURE 46H - To install side and top filler panels, remove
screws from top corners of both cabinets and the entire row
across the cooling coil cabinet.
Remove row of screws.
Remove
corner
screws.
Remove
corner
screws.
6. Prepare Cabinets to Install Filler Panels (See FIGURE 46H)
a) At the side corners of both the cooling coil cabinet and the
furnace, remove the factory-installed screws that attach the
cabinet tops.
b) Across the edge of the cooling coil cabinet, remove the row of
screws that attach the top.
the blockoff plate and drill a 7/8" hole. The hole should be
approximately even with the hole drilled in the downturn
plenum leg.
Third Hole:
On the cabinet leg on the entering air side of the cooling coil cabi-
net, measure up 10" (254mm) from the bottom pan. At that height,
measure in 4" (102mm) from the edge and drill a 7/8" hole.
b) On the outside of the furnace section
(where the flanges were joined in Step 4),
locate the three hole plugs. Remove the
center plug exposing a 7/8" hole in the
cabinet leg. See FIGURE 46F.
c) Run the wires attached to the damper mo-
tor 1) out through the hole in the dis-
charge plenum leg into the cooling coil
cabinet, 2) through the blockoff plate,
across the coil cabinet, 3) out through the
hole in the cooling coil cabinet leg, and 4)
into the furnace section.
d) On the bottom of the electrical box in the furnace section, remove the
hole plug that is below the terminal blocks. Route the damper motor
wires up through the hole and into the electrical box. Attach accord-
ing to the connections on the wiring diagram. Refer to sample in
FIGURE 46G.
7. Install the Cabinet Side Filler Panels (See FIGURE 46J)
Place a piece of the supplied insulation against the inner panel of the
cooling coil cabinet. Slide the filler panel into place and attach with
1/2" sheetmetal screws. Repeat on the other side. NOTE: It may be
easier to slide the filler panels in place with the door panels re-
moved.