Document Outline

• CT-31 Series
• Revision History
• Preface
• Table of Contents
• List of Figures
• List of Tables
• 1 Introduction
  • 1.1 Overview
  • 1.2 Features
  • 1.3 Block Diagram
  • 1.4 Product List
    • Processor Blade
    • Rear Transition Module
  • 1.5 Package Contents
    • Processor Blade
    • Rear Transition Module
• 2 Specifications
  • 2.1 CT-31 Specifications
  • 2.2 Power Requirements
    • Power Consumption
• 3 Functional Description
  • 3.1 Processor
    • Intel® Atom™ Processor N450
    • Intel® Atom™ Processor D510
  • 3.2 Chipset
    • Intel® ICH8 Mobile I/O Controller Hub
  • 3.3 Super I/O
  • 3.4 Battery
• 4 Board Interfaces
  • 4.1 CT-31 Blade Layout
    • CT-31 Assembly Layout
    • System LEDs
    • CT-31 PCB Layout
  • 4.2 CT-31 Connector Pin Assignments
    • CompactFlash Connector on DB-3610CF
    • DB-3610CF Connector (CN2)
    • CompactPCI J1 Connector
    • CompactPCI J2 Connector
  • 4.3 CT-31 Switch Settings
    • Clear CMOS Switch (SW4)
    • VGA/GPIO Mode Switches (SW1, SW3)
  • 4.4 DB-3610CF Adapter Board
    • Installing a CF Card
    • Removing the DB-3610CF Adapter Board
  • 4.5 cPCI-R3610T RTM Board Layout
  • 4.6 cPCI-R3610T RTM Connector Pin Assignments
    • USB Connector on RTM
    • VGA Connector on RTM (DB-15)
    • Gigabit Ethernet Connectors on RTM (RJ-45)
    • Serial Port DB-9 Connector on RTM (COM2-3)
    • Serial Port Box Header on RTM (COM2/3)
    • Serial ATA Connectors on RTM
  • 4.7 cPCI-R3610T RTM Switch Settings
    • COM2 Mode Selection Switches on RTM (SW1~SW4)
    • COM3 Mode Selection Switches on RTM (SW5~SW8)
• 5 Driver Installation
• 6 Utilities
  • 6.1 Watchdog Timer
    • Using the Watchdog in an Application
    • Sample Code
• 7 BIOS Setup
  • 7.1 Starting the BIOS
    • Setup Menu
    • Navigation
    • Hotkey Descriptions
  • 7.2 Main Setup
    • System Time/System Date
  • 7.3 Advanced BIOS Setup
    • 7.3.1 CPU Configuration
      • Max CPUID Value Limit
      • Execute-Disable Bit Capability
      • Hyper-Threading Technology
      • Intel® Speedstep™ Tech
      • Intel® C-State Tech
      • Enhanced C-State Tech
    • 7.3.2 IDE Configuration
      • ATA/IDE Configuration
      • Configure SATA as
      • IDE Master/Slave
    • 7.3.3 Super IO Configuration
      • Serial Port1/2 Address
      • Serial Port1/2 IRQ
      • Serial Port3
    • 7.3.4 Hardware Health Configuration
    • 7.3.5 USB Configuration
      • Legacy USB Support
      • USB 2.0 Controller Mode
      • USB Functions
      • USB 2.0 Controller
      • USB Mass Storage Device Configuration
    • 7.3.6 AHCI Configuration
      • SATA Port0/1/2
      • S.M.A.R.T
    • 7.3.7 Remote Access Configuration
      • Remote Access
      • Serial Port Number
      • Serial Port Mode
      • Flow Control
      • Redirection After BIOS POST
      • Terminal Type
      • VT-UTF8 Combo Key Support
      • Sredir Memory Display Delay
  • 7.4 Advanced PCI/PnP Settings
    • IRQ Channel
  • 7.5 Boot Settings
    • 7.5.1 Boot Settings Configuration
      • Quick Boot
      • Quiet Boot
      • Bootup Num-Lock
  • 7.6 Security Setup
    • Password Support
      • Two Levels of Password Protection
      • Remember the Password
    • Supervisor Password
    • User Password
    • Change Supervisor Password
    • Change User Password
    • Clear User Password
    • Change Supervisor Password
    • Change User Password
  • 7.7 Chipset Setup
    • Onboard LAN BIOS Init
    • Initial Graphics Adapter
  • 7.8 Exit Menu
    • Save Changes and Exit
    • Discard Changes and Exit
    • Discard Changes
    • Load Optimal Defaults
    • Load Failsafe Defaults
• Important Safety Instructions
• Getting Service