Angelcare AC401 Deluxe - Manual (Page 9)

Movement Only
Sound Only
“TIc”, Sound & Movement
Sound & Movement
“TIc” & Movement
IF THE ALARM DOES NOT SOUND
• Avoid contact with crib while Sensor pad is in operation.
• place crib near a supporting wall.
• Adjust the Sensor pad sensitivity level.
1 2
TO TEST SENSOR PAD
MoveMent or “tIC” Mode need to be aCtIvated:
MOVEMENT ALARM
• If NO movement is detected after 15 seconds you will hear a single “TIc” pre-alarm
sound from the Nursery Unit.
• If after a further 5 seconds there is still NO movement detected both the parent Unit
and Nursery Unit speakers will a emit loud warning sound.
• Nursery Unit icon flashes on the parent Unit
• Green light on the Nursery Unit will turn off to indicate NO movement is being
detected.
1) Move your hand lightly on the mattress.
pendulum icon will appear
on parent Unit indicator bar.
It will move as you move your
hand and trigger a “TIc” sound.
2) Remove your hand from the mattress.
After 15 seconds you will hear a
“TIc” pre-alarm sound, and 5 seconds
later the Movement Alarm will trigger.
3) Repeat by moving your hand lightly in
all four corners of the mattress. Ensure
the Nursery Unit Movement Indicator is
still flashing.
5.3 - CHANGING THE MOVEMENT AND SOUND MONITORING FUNCTIONS
TO SET DETECTION MODE:
3
2
1
1) press the MENU button once and
the flashing icons will appear.
2) Use the UP and DOWN Arrows to select
your preferred detection mode.
3) press the SELECT button to confirm
your choice.
4) press the MENU to view the next option,
or EXIT if you wish to stop programming.
If you press the MENU button for too long
the unit will go in to connection mode and the
Out-of-Range indicator will start flashing. If this
happens, wait 20 seconds and then press
the
MENU to start again.
5.1 - MENU ACCESS AND CHANGING THE SETTINGS
STEP 5 - TESTING AND GETTING TO KNOW YOUR MONITOR
The Angelcare ® monitor can be used with the pre-program factory settings
or you can also customise your settings to your preference.
IMPORTANT
When in MENU or SUB-MENU modes,
sound transmission between parent
and Nursery Units will be temporarily
deactivated.
All changes and
adjustments made
in the main MENU and
SUB-MENU will not be
activated unless you
confirm them by pressing
the
Select button.
The MENU settings are accessed by using the MENU button on the parent Unit.
The MENU functions are in a loop. Each time you press the MENU button briefly you
move on to the next MENU function. The MENU functions are in the following order:
NOTE:
By continuing to press the MENU button you
will be continuously moving through the loop.
Once you have selected your preferred settings
you must press SELEcT and then EXIT or your
changes will not be saved.
“ TIC”: Allows you to detect baby’s
movements as well as hear a TIc sound
at each movement.
Sound Only: Allows you to detect
the baby’s sounds. Movement detection
will be deactivated.
Movement Only: Allows you to detect the
baby’s movements without the TIc sound.
SENSOR PAD FUNCTIONS:
IMPORTANT
When in MENU or SUB-MENU mode
NO sound, alarm or vibration will be
emitted from either the parent Unit
or the Nursery Unit even if they were
activated before pressing the MENU
or SUB-MENU mode.
pRESS 1 TIME: “TIc”, Sound & Movement ....................... STEp 5.2 & STEp 5.3
pRESS 2 TIMES: Out of Range ............................................... STEp 5.4
pRESS 3 TIMES: Sound Transmission ......................................... STEp 5.5
pRESS 4 TIMES: Alarm ....................................................... STEp 5.7
pRESS 5 TIMES: Temperature................................................. STEp 5.9
5.2 - SENSOR PAD
17 16