Grandview GPCM-C - Manual (Page 2)

H
205mm
160mm
205mm
255mm
B C
3°
30°
3°
security holes
special
255mm
1
8 0
m
m
Top View
Diagram for applicable projector area
This projector lift must be installed above the bottom of projector (length 205mm; width 160mm).
Figure 1. Multifunctional arm is available for this projector lift and applicable projector area will be
increased (length 255mm; width 205mm)
Figure 1 Figure 2
Front View
Components and Accessories
GPCM-B is combined by GPC and GPM .
GPC
Assembly
The main bar and the subsidiary bar are fixed together from factory.Loosen
the screens of main bar③ and subsidiary bar④ . The distance between
projector and ceiling can be adjusted according to the distance of install holes
between main bar③ and subsidiary bar④ . Please refer to H in specification
table.
(Note: GPCM-C100 is no subsidiary bar and no stretch function).
③ ④
GPM
Assembly
1.GPM is combined by top bracket and low bracket . Press the
release button for separating the top bracket and low bracket.
2.There are special security holes for avoiding the falling of
projector (cooperate with security steel wire).
Usage
1. Press the release button for separating the top bracket⑦ and low
bracket⑧ , refer to figure 3 and figure 4. Then, adjust the half-cycle
junction⑤ and ensure that the groove of half-cycle junction to be
align the direction of security lock⑨ , and then put it on the
subsidiary bar
after assembling. Finally, the glider is installed on the
half-cycle junction for fastening the main bar⑥ as the figure.
2. Connect the projector and low bracket . Figure 5
⑦ ⑧
Figure 3 Figure 4 Figure 5
Three steps for installation
A. Please install GPC support
bar assembly on the ceiling B. Please connect the GPC
support bar assembly and
GPM projector fixation C. Adjust your desired angle.
GPC GPM
⑦
⑧
⑨
⑩
⑩a
⑩b
①
②
③
③b
④
③a
④a
⑤
⑤b
⑥
Specifications
Adjust distance
for each grid
Load
Optional Accessories
( ) Support Bar、Multifunctional Arm
Product Name
The length of support bar
Specification for Multifunctional Arm
400/600/800
30x355/30x295
Specifications
Unit(mm)
Unit(mm)
GPCM-C
/
Model
Accessories
M4x10 Pressing Screw (4pcs)
M4x5 Pressing Screw (2pcs)
M4x5 Positioning Screw (2pcs)
M3x10 Cross Machine Screw(4pcs)
M4x10 Cross Machine Screw(4pcs)
M5x10 Cross Machine Screw(8pcs)
M5x30 Cross Machine Screw(4pcs)
M3x20 Cross Machine Screw(4pcs)
M4x20 Cross Machine Screw(4pcs)
M5x20 Cross Machine Screw(4pcs)
M3x30 Cross Machine Screw(4pcs)
M4x30 Cross Machine Screw(4pcs)
M6 Drop In Anchors(3 sets)
16x10 Rubber Insert(4pcs)
16x20 Rubber Insert(2pcs)
Spanner (1pc)
Washer(4pcs)
Spring Washer(4pcs)
Parts:
① Base (1pc)
② Ornament Cover (1pc)
③ Main Bar (1pc)
③a Front Ornament Board
③b Back Ornament Board
④ Subsidiary Bar(1pc)
④a Ornament board for
subsidiary bar
⑤ Half-Cycle Junction (1pc)
⑤b Glider (1pc)
⑥ Main Screw (1pc)
⑦ Top Bracket (1pc)
⑧ Low Bracket (1pc)
⑨ Security Lock (1pcs)
Optional Accessories:
Multifunctional Arm
⑩ Multifunctional Arm (2pcs)
⑩a Fixer (2pcs)
⑩b Ornament Board (8pcs)
A
16
25kg