Grandview GPCN-E - Manual (Page 2)

1-1
1-2
1-3
2-1
2-2
2-3
2-6
2-4
2-5
1
2
GPCN-E200 GPCN-E3540 GPCN-E4560
Perpendicular
to the ground
Parts
GPCN-E is combined by GPCN and GPE
GPCN Main Bar Overview
1-1 Top Cap
1-2 Fixation
1-3 Sliding Adjusting Hole
2-1 Main Bar
2-2 Subsidiary Bar
2-3 Front Ornament Board
2-4 Back Ornament Board of Main Bar
2-5 Back Ornament Board of Subsidiary Bar
2-6 Moving Button
GPE Adjusting Overview
3-1 Adjuster
3-2 Horizontal Adjusting
Button
3-3 Vertical Adjusting
Button
3-4 Rotation Adjusting
Screw
4-1 Installation Bracket
4-2 Installation Arm
4-3 Adjustable Screw
4-4 Sliding Installation
Button
4-5 Installation Base
Accessories:
① 6x50 Wood Screw (4pcs)
② M5x16 Philips Screw (6pcs)
③ M5x8 Philips Screw (6pcs)
④ M3x8 Philips Screw (4pcs)
⑤ M4x8 Philips Screw (4pcs)
⑥ M5x8 Philips Screw (4pcs)
⑦ 6x25 Tapping Screw (4pcs)
Scope for installation (Installation hole of projector):
Maximum scope for installation:390mm diameter
Minimum scope for installation:20mm diameter
Note: Connect the installation arms to the projector conversely for different installation
holes of projector.
Scope
Maximum diameter: 390mm Minimum diameter: 20mm
Scope for installation (H is the distance between ceiling and projector)
The H of GPCN-E200 is 250mm
The H of GPCN-E3540 is 350mm~400mm
The H of GPCN-E4560 is 450mm~600mm
Scope
Install the fixation on the ceiling (screws of accessory ① or ⑦ ) as
figure 1, and the fixation also can be installed on the ceiling which
angle is less than 15°as figure 2. GPCN-E can be installed to the
concrete-roof with ceiling or without ceiling, such as figure 3 and
figure 4.
figure 1
figure 2
figure 4 figure 3
Steps of installation
Steps of installation
Connect the adjuster to GPCN Main Bar Overview, and then fasten
the screws (accessory ② ) as figure 5. Afterward, slide the
Adjustment Overview (projecter has been installed) to adjuster,
and the fasten the screws (accessory ③) as figure 6.Finally install
the top cap to the main bar, and then invaginate the spring. as
figure 7
figure 5
Details of installation
Wires collection
If the volume of power wire is less than diameter of main bar (2-1) that
please put this power cord inside the main bar directly. But if the volume
is greater than the diameter, please take apart back ormanent board
(2-4 and 2-5) and positioning button (2-6) from main bar (2-1)as
figure8. And then stay the power wire into the main bar (2-1)as figure 9.
Finally, re-install the back ornament board (2-4) from the other end,
and then install positioning button (2-6) and back ornament board (2-
5), figure 10.
figure 8 figure 9 figure 10
figure 6
4-1
4-2
4-3
4-4
4-5
3-4
3-1
3-2
3-3
H
H
H
figure 6
figure 7