Installation instructions, Mounting the i-420-em-a, Mounting the threaded body test switch (tbts) – IOTA I-420-EM-A User Manual
Page 2: Wiring, Labels, Completing installation, Lamps operated, Illustration 1 downlight fixture
Page 2
Illustration 1 Downlight Fixture
FLEX “A”
JUNCTION
BOX
CEILING
TILE
A.C. BALLAST &
LAMP SOCKET COMPARTMENT
FLEX “B”
SWITCH BOX
TEST SWITCH
CHARGE LIGHT
I-420-EM-A
TBTS
2. MOUNTING THE I-420-EM-A
When used with ceiling mounted downlight fixtures, the
I-420-EM-A should be mounted on the fixture above the
ceiling. The flex conduit marked “A” should be wired into the ballast/lamp compartment or to an electrical junction
box on the fixture which allows access to the ballast/lamp connections. Refer to Illustration 1 for typical mounting.
When battery packs are remote mounted, consult Customer Service for the maximum allowable distance between
the battery pack and the lamp.
3. MOUNTING THE THREADED BODY TEST SWITCH (TBTS)
Cut a single gang switch box into the ceiling tile adjacent to the fixture within reach of the
I-420-EM-A flex
marked “B”. After mounting the switch box, connect flex “B” to the box and route all leads inside the box. Refer to
Illustration 1 for typical mounting.
4. WIRING
A.
When
the
I-420-EM-A is installed on the same branch circuit, refer to Illustration 2, Figures A and B for input
wiring. When installed on separate branch circuits, refer to Illustration 2, Figures C and D for input wiring. Per
NEC, the
I-420-EM-A and A.C. ballast must be on the same panel board.
B. The
I-420-EM-A requires an unswitched A.C. power source of either 120 or 277 volts; therefore, when used
with switched fixtures, the
I-420-EM-A input must be wired ahead of the switch. Refer to Illustration 2 for
switched and unswitched fixture wiring diagrams.
C. Refer to the wiring diagrams on the back page for the proper wiring. For wiring diagrams of ballasts not shown,
consult our Customer Service.
5. LABELS
Attach the appropriate labels adjacent to the
TBTS. Annotate Re-lamping label for lamp type and wattage. The
Caution and the Re-lamping labels must be on the fixture in a readily visible location to anyone attempting to ser-
vice the fixture.
6. COMPLETING INSTALLATION
When the installation is complete, switch the A.C. power on and join the
I-420-EM-A unit connector.
INSTALLATION INSTRUCTIONS
CAUTION: Before installing, make certain the A.C. power is off and the I-420-EM-A unit
connector is disconnected.
INSURE WIRING IS IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE AND LOCAL REGULATIONS.
N
O
I
T
P
O
P
M
A
L
E
P
Y
T
Y
C
N
E
G
R
E
M
E
N
O
I
T
A
R
E
P
O
T
E
L
O
I
V
S
D
A
E
L
1
2
3
10W-32W
42W-57W
One Lamp
One Lamp
Two Lamp
Compact
Compact
Compact
Connected
Disconnected
Connected
10W-18W
4
5
6
18W
24W
36W
Long
Compact
Long
Compact
Long
Compact
One Lamp
One Lamp
One Lamp
Connected
Connected
Connected
Compact
Two Lamp
Disconnected
26W
7
1. LAMPS OPERATED
Refer to the chart for the type of lamp(s) operated and the number
of lamps to be operated in the emergency mode.If you have any
questions regarding specific lamps, contact Customer Service.
The
6
″ violet leads provide the lamp selection option. The unit
is shipped from the factory with the leads disconnected and
capped. When used with particular lamp types, violet leads
should be connected to one another. Refer to the chart for
lamp selection options.